Jump to content
SAU Community

Recommended Posts

Hey,

I can do 6x of the BOSCH 2200cc injectors for $830 incl. delivery.

This would include extensions to suit either 11mm or 14mm o-ring size and Denso plug's.

Let me know what you think,

Brendan

(VM)

hey brendan can i grab x6 1600cc to suit/fit a vq35det and pm me your bank details

thanks

rossi

  • Replies 191
  • Created
  • Last Reply

Top Posters In This Topic

hey brendan can i grab x6 1600cc to suit/fit a vq35det and pm me your bank details

thanks

rossi

U have a new PM :yes:

  • 2 weeks later...

Price please on 6 x 650cc (or there abouts) top feed injectors for ER34 RB25T NEO (Direct fit)

Hey!

How about some 725cc BOSCH EV14's, they won't be a straight fit but very close to. Very common upgrade injectors like the ID unit's.

I can do a set of 6x with extensions and plugs for $640 incl. delivery.

Let me know,

Brendan

(VM)

  • 2 weeks later...

Can I please get a price on 550cc x 6 to suit rb25, and if you do 740-750cc can I get a price on them also, cheers :)

Hi mate,

Sure thing are these R34 top feed unit's or side feed?

Cheers,

Brendan

(VM)

Ah my apologies, rb25 s1, top free to suit 11mm o ring (hks rail)

R33.

Cheers

Ok that makes things easier!

A full set of 6x EV14 BOSCH injectors would be the way to go.

These would be come with extensions to suit 11mm o-ring and plugs.

For 550cc would be $560, or 725cc would be $600.

Let me know what you think,

Brendan

(VM)

Hey mate in response to the convo,

Are you located in Sydney? These injectors will fit the top feed hks rail on a greddy plenum yes? Also you mentioned extensions, Assuming they this is for the electrical plugs?

Thanks,

Gav.

Was meant as a pm but for some reason wouldn't work.. Lol

haha all good.

We are located in Melbourne, and the extensions turn the injectors into a full size unit (11mm o-ring or 14mm o-ring) and the plugs are US CAR ones.

- Brendan

(VM)

Ah ok sweet, sorry I'm not overly teched up on electrical looms n plugs names / models? Will they plug in to the existing loom on the stock rb25 s1 harness?

Sorry to be a pain mate, just looking for a direct fit,

Cheers

Ah ok sweet, sorry I'm not overly teched up on electrical looms n plugs names / models? Will they plug in to the existing loom on the stock rb25 s1 harness?

Sorry to be a pain mate, just looking for a direct fit,

Cheers

Hi,

All good, na in most cases you will need to hard-wire it with the plug supplied.

- Brendan

(VM)

Ok Kool so I just had a good talk to the shop tuning my car today, I'm going to go for 1000cc injectors, I need something to fit top feed, 11mm o ring and to suit loom or if not supply plugs to be re wired ect... If I could grab a price that would be great,

Also whets the shipping turnaround time on these to Sydney? Cheers




  • Similar Content

  • Latest Posts

    • What 1.5 way? There's no such thing really as a 1.5 way, just different ways of explaining 2 ways with different ramp rates. HOWEVER. In any driving in a straight line your 1.5 or 2 or 1.7 way should have no clunking at all. With the clutch fully depressed the diff should be silent (unless it's welded but I'm assuming it's not). Something aint right here.
    • Clutch is a spec brand, new clutch system,( PP, flywheel, friction disc, etc. pull type) installed 100 miles ago, with no problems.
    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drove beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
×
×
  • Create New...