Jump to content
SAU Community

R34 Gtt Wheels 17X7.5 +40

grae35

By grae35,
in Classifieds

 Share

Recommended Posts

grae35 Collaborator

grae35

Posted
Posted

Set of 4 R34 GTT OEM Alloy wheels in near new condition with no gutter rash. They are 17" x 7.5" with +40mm offset.

post-54464-0-75677000-1334470473_thumb.jpgpost-54464-0-34618000-1334470527_thumb.jpgpost-54464-0-23802400-1334470542_thumb.jpgpost-54464-0-61010200-1334470559_thumb.jpgpost-54464-0-05354100-1334470575_thumb.jpg

Purchased these to use them as skidders on my V35 but decided they are in too good a condition to waste like that.

So have decided to sell them. $400 ono.

Link to comment
https://www.sau.com.au/forums/topic/397788-r34-gtt-wheels-17x75-40/
Share on other sites
grae35 Collaborator

grae35

Posted
  • Author
Posted

Not sure about 32 gtr fitment. stud pattern will be right but will ask some guys who may know if they will have enough clearance from body/guards/suspension.

grae35 Collaborator

grae35

Posted
  • Author
Posted

They may be able to fit but would look ridiculous

Don't know about that. I have looked at leaving the the centre covers off and putting in some of those cheap os wheel centres. You can even get red/black 'GTR' in OEM styling. Changes the whole look of the wheel.

  • 2 weeks later...
  • 3 weeks later...
  • 4 weeks later...
  • 3 weeks later...
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R32 gtr transmission strength, billet plate

      By GTSBoy · Posted

      Just put skinny tyres on it.
    • cosline
      R32 gtr transmission strength, billet plate

      By cosline · Posted

      Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • Piggaz
      R32 gtr transmission strength, billet plate

      By Piggaz · Posted

      You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • The Bogan
      NC MX5

      By The Bogan · Posted

      So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
×
×
  • Create New...