Jump to content
SAU Community

Recommended Posts

  • 4 weeks later...
  • Replies 151
  • Created
  • Last Reply

Top Posters In This Topic

  • 2 months later...
  • 2 weeks later...
  • 2 weeks later...
  • 3 weeks later...
  • 2 weeks later...

HKB boss kit sold sorry.

This is what's left:

New parts

Mazda Air temp sensor (for PowerFC D-Jetro) (brand new) $120
S14 'Edge' Side skirts, unpainted white gelcoat (brand new) $250
S14.5 Origin +25mm conversion fenders (brand new) $450
S14 Origin +50mm rear fenders (brand new) $450
S14 light weight fibreglass doors (brand new) $900
S14 Full Lexan window kit (rear window with NACA vents, rear quarters, driver and passenger door windows with slider window kits) (brand new) $1,050

Used parts

Factory
S15 factory rear boot spoler with led's, pewter colour $120
S15 JDM factory steering wheel with airbag $230

S15 front factory fenders (metal) no damage, no repairs $250 each

S15 factory rear bar $50

S15 factory sway bars $80 the pair
S15 boot lid and ducktail spoiler (not separating, duck tail is sikaflex'd and bolted on to boot lid) $300

S14a rolling shell, 6 point welded roll cage, white. Interior getting painted fresh white before sale.

Aftermarket

Greddy engine oil cap $40

S15 Hybrid aluminium radiator $250

S15 c-west front bar $350
S14/S15 Nismo springs and struts (lower than factory, very comfortable on street) $550
S13/180sx TRUST 19 row oil cooler kit, thick quality trust core, for S13/180sx with filter relocator $600
HKS Super Sequential SQV BOV, genuine HKS, mounted on evo 8/9 hot pipe $300
ATP 'Frank' turbo, with stainless steel manifold, will fit s14/15 SR20det, good for around 240-250rwkw with stock cams. Braided lines included. $1100ono
C-west genuine carbon fibre GT-wing, mounted on matte black wrapped S15 boot lid $1,100

R34 GTR Cusco Type-40 aluminium strut tower brace $220
R34 GTR C-west N1 front bar (genuine), carbon fibre (painted black), will need respray/minor repairs $700
R34 GTR C-west carbon fibre cannards for N1 bar $350
R34 GTR/GTT Nismo GT LED tail lights $1,200
R34 GTR Alcon 6-pot front 365mm brake kit, 4-pot rear 330mm brake kit. Ferodo DS3000 pads all round $6800

RAYS LE37's Top Secret Limited Edition Gold 18 x 10.5 +15 all round (rare, don't really want to sell these) $4000
SSR Type-C 17 x 9.5 +15 PAIR ONLY, white, average condition for age, no buckles $1000
** can post wheels interstate if needed at buyers cost **

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • @Murray_Calavera  If I were an expert I wouldn't be in here looking for assistance.  I am extremely computer literate, have above average understanding on how things should be working and how they should tie together.  If I need to go to a professional tuner so be it, but I'd much rather learn and do things myself even if it means looking for some guidance along the way and blowing up a few engines. @GTSBoy  I was hoping it would be as simple as a large vacuum leak somewhere but I'm unable to find anything, all lines seem to be well capped or going where they need to be, and when removed there is vacuum felt on the tube.  It would be odd for the Haltech built in MAP to be faulty, the GTT tune I imported had it enabled from the start, I incorrectly assumed it was reading a signal from the stock MAP, but that doesn't exist.  After running a vacuum hose to the ECU the signal doesn't change more than 0.2 in either direction.   I'll probably upload a video of my settings tomorrow, as it stands I'm able to daily drive, but getting stuttering when giving it gas from idle, so pulling away from lights is a slow process of revving it up and feathering the clutch until its moving, then it will accelerate fine.  It sounds like I need to get to the bottom of the manifold pressure issue, but the ignition timing section is most intimidating to me and will probably let a pro do that part.  Tomorrow I'll try a different vacuum line to T off of, with any luck I selected one that was already bypassed during the DBW swap. @feartherb26  I do have +T in the works but wanted to wait until Spring to start with that swap since this is my good winter AWD vehicle.  When removing the butterfly, did it leave a bunch of holes in the manifold that you needed to plug?  I thought about removing it but assumed it would be a mess.   I notice no difference when capping the vacuum line to it or letting it do its thing.  This whole thing has convinced me to just get a forward facing manifold when the time comes though.
    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
×
×
  • Create New...