Jump to content
SAU Community

Recommended Posts

Hi Guys

So i have just installed 3 gauges into my R34, they are the ones from Justjap with peak recall & warning.

Does anyone know if its possible to disable the beep when the gauge is doing the opening ceremony??

Also the middle gauge is a wideband sensor, i got it direct from Autogauge. Every time i take my foot of the throttle it goes to full lean which is all good but then the warning alarm goes off & keeps going off until i put my foot back on the throttle. Does this seem right?

I thought it may just need to be calibrated which is done by pushing a button on the control box however the instructions do not state whether the engine needs to be running or not.

post-86207-0-18050500-1335150435_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/398427-autogauge-warning-sound/
Share on other sites

Haha I feel your pain.. I have tried but unless you are willing to open the gauge you may have to put up with it.. With the other gauge iirc hold down the peak button which should then move the needle to where the warning limit is currently set. Slide the button upwards a tiny bit and you should see the needle move in small increments. From there set it where u want the warning to come on.

Thanks man, yeah the other gauges are all good iv set the warning but the wideband sensor just goes straight to lean & the alarm goes off. The car was stolen on Monday so if I dont get it back I might not put that same gauge in.

Nope it was a wideband sensor. Uses the bosch LSU4.9 Wideband Sensor. Its not one of those crappy ones off just jap. Got it from Autogauge direct. Only flaw is the fact that the alarm comes on every time my foot is off the throttle. Gonna send Autogauge an email & see if its normal.

post-86207-0-42546000-1335494085_thumb.jpg

^^ yep what he said... narrow band gauges are a bit of a gimmick.. ps. unlucky with the car being stolen.. perhaps they will return it when they get sick of the screaming gauges :P

Yeah that would be great if they returned it, its one of the first things i thought about was them getting angry coz it screemed everytime they changed gears.

Are Just jap STILL flogging those f**kin gauges?

I remember about 4 years ago I bought an A/F ratio gauge back when I had an R34, it came with a warning light & it would beep every single f**kin time I lifted off the throttle, bloody annoying

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
    • And if you have to drill the oil block, then just drill it for 1/4" and tap it BSP and get a 1/8 to 1/4 BSP bush. The Nissan sender will go straight in and the bush will suit the newly tapped hole. And it will be real strong, to boot.
    • No it doesn't. It just needs an ezy-out to pull that broken bit of alloy out of the hole and presto chango - it will be back to being a 1/8" hole tapped NPT. as per @MBS206 recco. That would be for making what you had in alloy, in steel. If you wanted to do just that instead of remote mounting like @Duncan and I have been pushing. A steel fitting would be unbreakable (compared to that tragically skinny little alloy adapter). But remote mounting would almost certainly be 10x better. Small engineering shops abound all over the place. A lathe and 10 minutes of time = 2x six packs.
    • Ahh. Well the block damage is a problem, you really need to run a tap or thread chaser through it to see if the threads can be saved, but any chips are likely to be bottom end bound which is bad. Earls seem to have what you need if you want to stick with mounting direct on the block: https://rceperformance.com.au/parts/earls-straight-adapter-1-8-npt-male-to-1-8-bspt-female.html, but as I said above I'd recommend remote mounting the sender
    • I'm not quite understanding or I'm missing steps here, (I appreciate people are trying to inform my brain but I am of the dumb, especially today) - All I want to do is mount the male BSPT of the OEM sender into the system somewhere without it snapping the adapter via vibration. The Nissan sender has a male 1/8 BSPT output. The block has a (very destroyed) 1/8 NPT input. I'm not really sure how a lathe assists with that, and also don't know anybody with a lathe, nor specifically what I would want to buy. I'm not really sure how adding additional adapters creates a better, more leak proof resilient seal here.
×
×
  • Create New...