Jump to content
SAU Community

Turbo Timer.

mindflux

By mindflux,
in General Automotive Discussion

 Share

Recommended Posts

mindflux Mentor

mindflux

Posted
Posted

Ok, Im going to try this one last time..

I have a HKS Type-1 Turbo Timer that im planning to install into my R32 GTS-t this afternoon, however I have a slight problem.

I have no Electronic Experience what-so-ever

and to top that off the Instructions are in Japanese..

Now perform you run off and say 'Just by a harness' .. im saying right now Im not going to nor do I want to..

After much thinking, i think I have translated the instructions, and i need some one to tell me if this is correct.

Out the bakc of the Turbo timer, I have seven (7) wires..

the break down should be something like this (i think)

Red, Green, Blue (Double Stripe) - These three wires come together into a little plastic plug at the end.

I belive I cut this plug off and using solder i connect these 3 wires to the corrosbonding wires that come out of the key ignition?

Brown (Single Stripe) - I think this is ment to connect to some wire to read my REVs, however i do not know which wire or its location

Blue (Single Stripe) - Same as above, however I think this wire connects to my SPEED wire, yet i dont know where it is or what it looks like

Black (Single Stripe) - I think this is my 'Negative' wire as it has like a hook on the end, I believe i attach this to the body of the car??

Grey (Single Stripe) - Im unsure what this wire does but i think it needs to be attached to the handbreak wire?

As you can see im not to sure as to what im doing, but if anyone can clarify this for me and let me know what to do etc, before i break something.

Thanks in Advance

Link to comment
https://www.sau.com.au/forums/topic/39876-turbo-timer/
Share on other sites
Dahtone Racing Grand Master

Dahtone Racing

Posted
Posted

i just hooked some thing like that up in a mates car not HKS but same sort of deal

Grey - Handbrake switch, goes to the handbrake switch the wire is next to the handbrake. take off all the centre console and join it to the wire comming off the handbrake.

Black - Earth, a good bare metal point.

Blue - Speed Wire, goes to wire #53 on the ECU harnes. The wire is yellow-green with a silver trace.

Brown - Rev wire, once again on the ECU harness how ver im not sure which wire im sure someone on here will know

Link to comment
https://www.sau.com.au/forums/topic/39876-turbo-timer/#findComment-816869
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      NC MX5

      By MBS206 · Posted

      Take a couple of the big ones back to "work", leave them in the big bin.   Will make a good boom when the garbage truck emptys it out... I've heard from another source about the boom when they had put I believe it was a 4cylinder engine in the big bins at Richmond base...
    • The Bogan
      NC MX5

      By The Bogan · Posted

      That idea has crossed my mind, I do a 5km walk everyday, this does take me past some bushland......I think you may be onto something 😉  That, plus 1 rock on every bin night might do the trick, it may take a year, but it could save me a couple of grand The only issue is the big 'Boonies", I have a few that weigh around 30-40kg, maybe they should be the first to go into the raised garden bed,  and then let the next owner deal with them....my daughter gets the joint when I kick the bucket, mums the word mate......LOL Noice......
    • V35_Paul
      Who has a Infiniti Q60, Q50 (V37)?

      By V35_Paul · Posted

      Wow. Did you call the car a Nissan Skyline?
    • MBS206
      NC MX5

      By MBS206 · Posted

      You're retired Mark, on bin night, go for a walk, kind of like you're doing the beep test. Put one rock in the first neighbours, come back, get another rock, go to the second neighbours, repeat over many weeks. All rocks eventually gone...
    • The Bogan
      NC MX5

      By The Bogan · Posted

      No chop chop of anything mate, it is what it is, plus, I don't want any air that isn't either going through the cooling stack or intake getting into the engine compartment increasing under bonnet pressure  Yeah, the Mazda Speed aftermarket intake above is less than ideal for multiple reasons, the requirement to remove the bumper every time you need to service the filter, and also smaller in diameter than the NC1 OEM one Weirdly, Mazda Speed is part of the Mazda motorsport division, "form over function" and $$$$$ for Mazda from unsuspecting punters I suspect  After some googling about them it seems they added no power, but do increase some induction noise Meh In other news, the electricians have been busy today at the house, and are back tomorrow finishing up all the security stuff and exterior lighting, they also added some lighting on the garage ceiling, which will come in handy when working in the garage when it's not freezing out there My Birdies raised garden bed also arrived today as well, which I'll put together and place tomorrow, it's a big tall Bessie, 74cm high, 92cm wide and 214cm long, this will come in handy as I am starting to get "stockpiles" of good soils from doing landscaping, some of the clean rock, namely the river stone, will go into the bottom of the bed for drainage, as well as the old Apricot tree that was out the back,  and when it's full, I'll grab another one, I will be growing enough veggies to keep me both busy as well as supplementing the shopping list I'm also awaiting another quote for a new Colourbond front fence, as the "1980 style cemented in rock edging" that was there and "fashionable at the time" looked arse, and my god, the amount of cement used to fix the rock was insane, it took 1.5 days for me to break out 12 meters of the stuff by hand, trim the bushes back to the fence line and dump it out the back of the joint to deal with at a later date,I will soon need a skip bin to tip it all Unfortunately they did alot of the cemented in rock around the joint, which I hate, so a few pallets of retaining wall blocks for around the front and back where the cemented in rock is will be required to bring it up to a standard, and look, that I will be happy with 12 meters worth of rock and cement Finished smashing the fence line and ready for a fence to be installed, yes, the lawns need some TLC and thickness, the previous owner trimmed the grass to the roots 😢, the TLC I can provide, and nature over time will do the rest And there's probably about another 40 meters worth of this landscaping abomination left to do around the front and back gardens, I'm guessing maybe 3 or 4 tons worth, tip fees for this will be a killer Meh, all in all I'm having fun and keeping busy, plus, it's good PT
×
×
  • Create New...