Jump to content
SAU Community

[Vic] Stock R34 Gtt Rb25Det Bov & Crossover Pipe.will Suit The R33 Gtst Also. Can Post Oz Wide!

G4orce
 Share

Recommended Posts

G4orce Veteran

G4orce

Posted
Posted (edited)

FACTORY OEM R34 GTT RB25DET BLOW OFF VALVE COMPLETE WITH THE ALLOY CROSSOVER PIPE

Removed from a 95,000km R34 GTT, In Excellent working condition.

Perfect for clearing those defects / epa or great for returning your car back to stock .

I have been told you can use it on a R33 Gtst also as they are the same.

What you see in the photo below is what you get.

Asking $100 ono . Pick up Taylorslakes - Melbourne or can post around Australia for an extra $15.

Pm Call or txt on 0422756270. cheers.

img0152ixrn.jpg

img0148vy.jpg

img0161ir.jpg

Edited by G4orce
  • 5 weeks later...
  • 2 weeks later...
  • 2 weeks later...
  • 2 weeks later...
  • 2 weeks later...
  • 2 weeks later...
  • 3 weeks later...
G4orce Veteran

G4orce

Posted
  • Author
Posted (edited)

Hardly needs another bump, but just wanted to point out that they don't suit R33. The Neo throttle body is very different and the Xover pipe is shorter.

thanks for letting me know,

Edited by G4orce
  • 3 weeks later...
  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you done the Ignition Sync Wizard in the AEM software?
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • MBS206
      RB25DE NEO with Haltech ECU

      By MBS206 · Posted

      You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • sonicii
      Could it really happen......

      By sonicii · Posted

      I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...