Jump to content
SAU Community

Fs: Hks Wastegate Actuator, 3'' Dump To Cat Pipe And 3'' Cat Back System

rb2534
 Share

Recommended Posts

rb2534 Rising Star

rb2534

Posted
Posted

I'm selling the bits that I have collected to mod my 34 but as I found a complete package I am unloading the parts I have already bought in order to fund the parts I'm fitting tomorrow. These bits were bought for my 34 4 door and the exhaust is to suit a 2 door, I was going to modify it to suit and the front pipe is been delivered to my house tomorrow so it will be available from then.

HKS wastegate actuator, mounting bracket has been cut but can be re welded to suit or modify an original one - $100

Similar to this one: http://www.ebay.com/...G-/260830910311

Just Jap Front pipe 3'', goes from the turbo to the cat - $100

Like this one: http://justjap.com/s...&cat=276&page=1

3'' Stainless Steel Cat back exhaust with cannon on the end, previous owner said it would be loud. I was going to use but have since found another complete system to fit 4 door direct - $200

Parts in Adelaide and will send interstate and will deliver locally, and can send pics if wanted

rb2534 Rising Star

rb2534

Posted
  • Author
Posted

No worries, yeah the front pipe is used I only bought it last week so I can sms you pics today when I go pick it up from been delivered and i will get a quote on freight but 100 delivered should be fine

rb2534 Rising Star

rb2534

Posted
  • Author
Posted

HKS can be sold in combo with boost controller

http://www.skylinesaustralia.com/forums/topic/402357-blitz-twin-sbc-spec-s-boost-controller/

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...