Jump to content
SAU Community

Recommended Posts

  • Replies 76
  • Created
  • Last Reply

Top Posters In This Topic

i think this is what i meant

http://www.skylinesaustralia.com/forums/topic/403217-r33-gtr-wheel-offsets/page__fromsearch__1

10 +18 will be swallowed up by a 33gtr. 10.5 +15ish ish looks good with a 285 or so.

18x10 +18 is for gtsts :nyaanyaa:

The thing is I've had these exact wheels on another 33 Gtr and they were flush, sorta. Not an inch inside the gaurd.

I mean work doesn't even make anything in the xd9 xt7 etc bigger then 10 wide +18.

I'd just like a fellow Gtr owner to try the rims on there car front and back

Thanks mate... That looks dame close to poking out at the rear.... tires would be 275s as ive already bought them. so could be a bit to sticky out for me?

You wouldnt be around ttp are would you? and mind if i could test fit on mine??

Looks like a fair bit of camber there - I reckon that is your problem. Get a spirit level and hold it vertically against the bottom of the rim and see how far in the top if tilted.

i hope so.. i was told it was running much, but this is by the same people who measured the offset of the rims wrong....

Can the rims almost sit straight up and down? or do they have to naturally have to lean back a little??

Thanks mate... That looks dame close to poking out at the rear.... tires would be 275s as ive already bought them. so could be a bit to sticky out for me?

You wouldnt be around ttp are would you? and mind if i could test fit on mine??

my wheels will only sit 6mm further out than yours. just get some slip on spacers if youre that worried dude

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
×
×
  • Create New...