Jump to content
SAU Community

Recommended Posts

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

Sorry - 5mm.

You have an adjustment problem. There is about 60mm of travel in the slave. you need to be able to force the piston/pushrod back inside. It should push back in with very minimal effort. If it cannot, your clutch pedal is overadjusted. Get someone to wind the pushrod looser while someone else pushes against the slave pushrod. As soon as the piston can push back inside the slave, leave your adjusment there. If you are still having problems after that, you might have a master cylinder pushrod length issue or if you used the old pushrod on the new master cylinder sometimes the ball section on the pushrod from the factory master is larger than the cup section in the back of the master cylinder piston so the old pushrod holds the piston forward by a mm or so. This is all it takes to block the recovery port in the master and prevent back filling into the cylinder. If you used the old pushrod on the new master, I'd check that before adjusting the pushrod any further.

You have an adjustment problem. There is about 60mm of travel in the slave. you need to be able to force the piston/pushrod back inside. It should push back in with very minimal effort. If it cannot, your clutch pedal is overadjusted. Get someone to wind the pushrod looser while someone else pushes against the slave pushrod. As soon as the piston can push back inside the slave, leave your adjusment there. If you are still having problems after that, you might have a master cylinder pushrod length issue or if you used the old pushrod on the new master cylinder sometimes the ball section on the pushrod from the factory master is larger than the cup section in the back of the master cylinder piston so the old pushrod holds the piston forward by a mm or so. This is all it takes to block the recovery port in the master and prevent back filling into the cylinder. If you used the old pushrod on the new master, I'd check that before adjusting the pushrod any further.

Thanks. I'll give that a shot tomorrow night.

I bought the master cylinder from Kudos Motorsport as per the link (http://www.kudosmotorsports.com/catalog/nissan-clutch-master-cylinder-genuine-nissan-skyline-r32-gtr-r33-gtr-r34-gtr-rb26dett-p-384.html)

By pushrod, do you mean the rod inside the master cylinder booster (the adjustable one) or the gold push rod in the picture of the master cylinder in that link?

Thanks

Thanks. I'll give that a shot tomorrow night.

I bought the master cylinder from Kudos Motorsport as per the link (http://www.kudosmoto...dett-p-384.html)

By pushrod, do you mean the rod inside the master cylinder booster (the adjustable one) or the gold push rod in the picture of the master cylinder in that link?

Thanks

Sorry I forgot you had a GTR. Disregard the ball on the pushrod comment - that is for GTST's only. It has the booster which you can't really go wrong with (unless you pulled the booster pin out)

Sorry I forgot you had a GTR. Disregard the ball on the pushrod comment - that is for GTST's only. It has the booster which you can't really go wrong with (unless you pulled the booster pin out)

All good. Booster pin was untouched. Simply replaced the master cylinder with a new one and installed it. Gravity bled the system, then bled by pumping the clutch and then gravity bled again.

Then had the same issue - Adjusted inside the cabin, I will take a photo of how far up it is adjusted tonight.

Edited by ls128

I have noticed that the peddle comes up more after i have been driveing for a bit and the clutch warms up. I should say too that it is fitted with a extreme extra heavy duty button clutch and presure plate and 10lbs chrome molly flywheel.

I will be changing the length of the push rodd to the master cylinder as the one on the slave is fixed length.

Also i have noticed that the stroke length of the peddle is only about 20mm i put this down to the face that it is adjusted incorrectly.

@ LCXU105 - Oh you meant you push the pedal down and it's only hard for 20mm of pedal travel?

I thought you were referring to the slave cylinder which is what we were talking about

If the clutch is bled and adjusted correctly then the only other thing that can cause it to pull the car forward when you start it in gear with the clutch down is if the clutch plate is bent (usually from improper installation by people on the ground hanging the box off the back of the engine for too long)

No m8 you have it wrong. car is not moveing foward at all and i was saying that the slave cyl rod can be pushed in 20mm when not in use and the peddle is hard at the top of the stroke for only 20mm of travel and clutch is fully ingaged. will be adjusting the rod on the master cyl so it is a little further down on the peddle stroke so i know it is not putting presure on the clutch.

No m8 you have it wrong. car is not moveing foward at all and i was saying that the slave cyl rod can be pushed in 20mm when not in use and the peddle is hard at the top of the stroke for only 20mm of travel and clutch is fully ingaged. will be adjusting the rod on the master cyl so it is a little further down on the peddle stroke so i know it is not putting presure on the clutch.

The first two lines were for you.

The second two were for LS128

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...