Jump to content
SAU Community

Recommended Posts

Power steering cut off while i was driving today. Took a tonne of muscle to move the steering wheel but it came back on after i straightened the wheel out. Also my RPM fluctuates up and down whilst idling. These issues don't always occur, it is really random.

Please help. Kind regards, Simon.

Also the RPM's dip low enough for the engine to cut off.

Edited by EarthShore

Obviously you know this is serious from having an accident point of view. brakes and steering affected.

By the time you feel it your engine has alsmost if not already stalled.

Normally I found when it happend to me to occur on corners. Seriously scary !!

Very rare when traveling in a straight line but occasionally had to keep the revs up at the lights.

I was thinking lack of fuel at one stage as it was normaly at qtr of a tank or less or round corners.

I didn't get to the bottom of it before significant work was undertaken on my GTR.

No Unfortuantely. I did a big end bearing.

Therefore had an engine rebuild. Whilst it was being rebuilt I had a lot of additioanl work done.

Personally I'd start by checking the flow of your fuel pump.

Could be time to replace fuel pump and repalce your fuel filter.

Hopefully someone like Jez and others can jump in on this thread.

I had the same issue whilst drifting. Car would cut out on entries and all the lights would come on dash for split second then it would come back to me.

Caused a lot if straightening and frustrating. Wouldnt as such surge/splutter and carry on. More just cut out and turn back on within a second or so.

Even did it with full tank. Changed fuel pump still no different, checked earths all seemed fine. Never got to the bottom of it.

my power steering becomes heavy after about 5 mins of driving, and im getting the rev drop when i stop, ive cleaned and resoldered afm, and changed the o2 sensor, ive also cleaned the aac valve which was black as the ace of spades! now im getting it but not as bad, ie its not stalling anymore! i think it could be a fuel pump earth issue, or the tps is not set correctly. ill be investigating this weekend.

It was the fix I least expected! But I think the gear box on the auto ha something todo with the peer steering fluid???????????? I'd check afm AAc and tps sensors and I suppose a gear box oil change couldn't hurt! I was genuinely shocked when I topped it up and 10 mins later the car was driving like new! Let us know how you get on tomorro mate!

Cleaned the AAC and checked the AFM but still didnt fix the idling issue. However I saw that the engines RPM could be manipulated by wiggling the bottom cord which connected to the TPS. I'm really starting to think it's the TPS. I ordered a new TPS and will fit it ASAP. I'll let you guys know how it goes. Cheers!

Make sure it's positioned right, I don't know how to do it but there is a thread on here about how to set your tps, even if you put a new one on but it's in the wrong position, it still wont work properly x

Thnx found it! Set the TPS to the correct voltage. It appears to have fixed the Idling problem, however it does idle too high now. I'm gonna have to do an idle reset tomorrow. Will let u know how it goes.

Also i lowered the idle using the screw on the AAC valve as much as I could. The idle still sits at a high 1200 rpm so I'm assuming I need to adjust the Idle using the idle screw on the ECU?

Edited by EarthShore
http://www.skylinesaustralia.com/forums/topic/404812-help-setting-tps-on-r33-s2/ if u have a S2 its the brown plug (bottom one) and the middle red wire :) cheers for the help. After setting the correct voltage to my new tps the car runs like a dream. As for the power steering problem it seems to have subsided for now :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Welcome to Skyline ownership. Yes, it is entirely possible parts websites get things wrong. There's a whole world of inaccuracies out there when it comes to R34 stuff (and probably 33 and 32). Lots of things that are 'just bolt on, entirely interchangable' aren't. Even between S1 and S2 R34's. Yes they have a GTT item supposedly being 296mm. This is incorrect. I would call whoever you got them from and return them and let them know the GTT actually uses 310mm rotors. Depending on where you got them from your experience and success will obviously vary.
    • Hi...a bit a "development" on the brakes. I spoke to the guys where i get brakes from...and they are saying that 296mm EBC are for R34 GT-T. I then went to their site: https://www.ebcbrakes.com/vehicle/uk-row/NISSAN/Skyline (R34)/ and search for my car(R34 GT 1998 - it has GTT brakes) and it show me this USR1229 number and they are rly 296mm rotors... So now iam rly confused... The rotors i have now on the car are 310mm asi shown... So where is the problem? Does the whole EBC got it wrong or my calipers are just...idk know what?  
    • Oh What the hell, I used to get a "are you sure you want to reply, this thread is XX months old" message. Maybe a software update remove that. My bad.
    • This is a recipe for disaster* Note: Disaster is relative. The thing that often gets lost in threads like this is what is considered acceptable poke and compromise between what one person considers 'good' looks and what someone else does. The quoted specs would sit absurdly outside the guards with the spacers mentioned and need  REALLY thin tyres and a LOT of camber AND rolling the guards to fit. Some people love this. Some people consider this a ruined car. One thing is for certain though, rolling the guards is pretty much mandatory for any 'good' fitment (of either variety). It is often the difference between any fitment remotely close to the guards. "Not to mention the rears were like a mm from hitting the coilovers." I have a question though - This spec is VERY close to what I was planning to buy relative to the inboard suspension - I have an offset measuring tool on the way to confirm it. When you say "like a mm" do you mean literally 1mm? Or 2mm? Cause that's enough clearance for me in the rear :p I actually found the more limiting factor ISNT the coilover but the actual suspension arms. Did you take a look at how close those were?
    • @GTSBoy yeah sorry i know thery are known for colors bud those DBA are too in colors 🙂 Green will be good enough for me  
×
×
  • Create New...