Jump to content
SAU Community

Recommended Posts

Hey guys I'm currently making 307rwkw with the following fuel setup ( custom fuel rail, 875cc injectors, adjustable fuel reg and a 044 pump ) an of corse the supporting mods to make that power. My question is I'll be doing some more work on it very soon and aim for 350rwkw is my current fuel setup enough for that power or should I be looking at doin a surge tank and another pump?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/404975-fuel-setup-for-350rwkw-r33-rb25/
Share on other sites

What car and fuel? On 98 it should be fine, on E85 those injectors might be a bit on the small side. You might also run into problems with your fuel lines, I've seen a few cars hit a wall in power at ~320rwkw with the standard fuel lines a restriction. Others have gone over 400. The pump will be pretty close to it's limit, but should still be ok.

360 kw on E85 here..... O44 is maxed on its safe limit, injectors and rail are ok (1000cc)...... Standard fuel line needed to be replaced in mine BUT pretty sure 33 won't need to be :)

I couldn't find his sig cause I'm on my phone:/ will check it out tonight on the puter.

Because I'm a nice guy ;) This is Matt's sig list:

Engine: Haltech PS2000, Wideband setup, ethanol content analyzer, GT3037-56T (.82 rear) with custom braided lines, Tial 44mm MV-R gate, custom dump pipe with heat wrapping, high flow cat and Apexi exhaust, HKS EVC 5 Boost Controller, 6Boost Manifold, Tomei 260 Type B Poncams, Exhaust cam gear, Gates Racing timing belt kit, Aftermarket Springs & Retainers, 4"intake with drift pod filter in custom JJ airbox, Plazmaman Pro series intercooler, Plazmaman piping, Plazmaman intake plenum and 66mm throttle body, Splitfire coil packs, GFB respons BOV plumbed back, Powdercoated covers by Craved Coatings, Black Works oil cap, Alloy Radiator air defelctor

Fuel: Bosch 044 fuel pump, XSPURT 1000cc injectors, HKS fuel rail powdercoated black by Craved Coatings, Billet fuel filter, SARD fpr, speedflow fittings.

Drivetrain: Exedy Cushioned Button clutch, Nismo 1.5 way diff, Nismo shifter.

Suspension: Tein SS coilovers, Front ISC adjustable caster rods, superpro camber kit, 27mm Selby swaybar. Rear ISC adjustable camber arms + Traction rods, Alloy locking rings & 24mm Selby swaybar.

Wheels & Brakes: 18" Works XT7's (F8.5 R9.5) powdercoated black, Kuhmo KU36 tyres, HEL braided lines, Endless front pads and rotors ,Endless pads rear.

Exterior: Carbon weather shields, Eyelinds & Bonnet lip.

Interior: Brown Davis Roll Cage, drift harnesses, Pioneer/Alpine/Fusion stereo.

Edited by Hanaldo
  • Like 1

Well Matt has always been a nicer guy than me! :P

Price for converting to E85 is pretty subjective mate, there's so many ways to do it. I've seen quotes from as low as $1500 all the way to $5000+. The way I believe to be the best and the way I would do it is also the way Matt has done it. Not cheap though.

  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
    • EMU Classic. For what I need it to do I see no reason to upgrade. Link and Haltech would both cost an extra chunk of money for a lot of unutilized features
×
×
  • Create New...