Jump to content
SAU Community

Recommended Posts

Selling my R34 Gtt 1999, in very good condition. Since being in Australia it has been a RacePace car, mechanically and tuned by Chris there. All mods have not had any shortcuts and all quality Japanese parts only. The car has had its 100k service last year and full tune so its running very well. Service oil, filter & plugs every 5000kms, no leaks at all. still have most receipts from Racepace, a lot of money spent.

Reggo: end of March

Number Plates: DCV034 included

RWC: NA (can be supplied at extra cost)

kms: approx 117,000

Motor :

RB25 standard engine

HKS GTRS Turbo (very responsive)

HKS Front Mount Intercooler

Z32 airflow meter

Nismo 480cc injectors

Apexi Power FC

HKS 3 inch Silent Power exhaust to with cannon (never had epa issues)

RacePace super high flow cat

044 Bosch fuel pump

3A Racing super high flow pod filter

Suspension:

BC BR Series coil overs (purchased December 2011)

Interior:

Power fc hand controller

Auto Meter Boost controller (reads PSI not bar)

Apexi automatic Turbo timer with batt voltage, o2 sensor & air/fuel reader

Pioneer double din DVD head unit

JL C2's 6" front splits & focal 6" rear speakers

Exterior:

Xenon HID's

Nismo genuine smoked front & side indicators

18 x 9.5" Black Koya Drifteks all round (perfect condition, no rash) +20 offset on rear & +34 on front sits perfect

Maxxis tyres all round, purchased December 2011 and still has 80% tread all round

Real carbon fibre wind deflectors

Real carbon fibre radiator cooling panel

Driveline:

Racepace fitted heavy duty clutch

C's Short shifter

Extras:

standard suspension front and rear

standard injectors

standard shifter

standard air box

Made about 250rwkw, will post a scan of the dyno sheet asap.

$20,000 ono

Car is located in Mill Park, VIC 3082

Will add more pics this week hopefully.

Thanks for looking,

Call or PM Ben on 0401350991

post-86274-0-98072100-1345985671_thumb.jpg

post-86274-0-00596200-1345985683_thumb.jpg

post-86274-0-53603300-1345985692_thumb.jpg

post-86274-0-20844800-1345985710_thumb.jpg

post-86274-0-05868300-1345985723_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/407899-r34-gtt-silver-very-clean-250rwkw/
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...