Jump to content
SAU Community

Recommended Posts

Rays Gram Lights 18x10+18 Pair No Tyres

Price: $800 Firm Looking for a quick sale

I've got this pair of rims which I no longer have use for. There is some scuff marks as shown in pics but they have not alter the working condition of the rims. They currently have tyres on them which aren't part of the sale.

Plenty of Dish

IMG_8272.jpg

Clear Coat coming off one of the rims

IMG_8275.jpg

Small Bump here which doesn't affect the working condition of the rim. Currently has a 235/40/18 on it and it's holding pressure fine

IMG_8277.jpg

Small Dint at the back which hasn't affected the working condition of the rim

IMG_8283.jpg

Contact Via PM or SMS

Located in Hurstville or Manly Area

0421079631

Benny

Link to comment
https://www.sau.com.au/forums/topic/408541-nsw-rays-gram-lights-pair-18x1018/
Share on other sites

  • 1 month later...
  • 6 months later...

Rays Gram Lights 18x10+18 Pair of 225/40 shagged see pics of tread

Price: $800


I've got this pair of rims which I no longer have use for. There is some scuff marks as shown in pics but they have not alter the working condition of the rims. They currently have tyres on them which aren't part of the sale.

They were plastidipped in blue which i've now removed but there a little bits of plastidip still mainly around where the lug nuts go just need some tlc to remove completely


20130419_171646_zpsc8078ea7.jpg

20130419_171659_zps78fe0353.jpg

20130419_171706_zps64604401.jpg

Condition of Tyres
20130419_171719_zps9a43d4ca.jpg

20130419_171727_zps5b33e91a.jpg

Plenty of Dish

IMG_8272.jpg


Clear Coat coming off one of the rims

IMG_8275.jpg


Small Bump here which doesn't affect the working condition of the rim. Currently has a 235/40/18 on it and it's holding pressure fine

IMG_8277.jpg


Small Dint at the back which hasn't affected the working condition of the rim

IMG_8283.jpg

Contact Via PM or SMS

Located in Hurstville or Manly Area


0421079631

Benny

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...