Jump to content
SAU Community

Recommended Posts

So the time has come to let my project go, have spent time and money and need to let it go in favor of other pursuits.

car made 160rmkw and 450nm @14psi could easly make more as running rich on top end so retune will fix it up, currently removed boost tee for roady and is running stock 12, still bloody quick.

Pics pending will be up shortly. Asking price, negotiable ,$14,000, just a rough estimate based off what i saw on carsales without roadies.

mods listing

engine: rb20det (out of r32)

rb20 box

rs yamamoto chiped ecu

locked 4.33 diff

hight flowed r33 turbo

52mm radiator

twin el thurmo fans

fmic

3" turbo back exhuast with twin pipe magnaflow muffler and high flow cat

bosch 040 fuel pump

catch can

gfb boost tap

new water pump timing belt power steering pump and all belts.

new welsh plugs and rear main

pbr heavy duty clutch.

new clutch master and slave

suspention and brakes:

5 stud conversion

r32 calipers all round

new pads and roters all round

new brake master cylinder

new bc coilovers

new jic front caster arms

new jic rear camber arms

new (not fitted) gk tech rear toe arms

new (also not fitted) tie rod ends

front and rear top strut braces

new soft brake lines

interior:

blue dildo shifter

drift wheel

drift button

r33 4 door front seats

dash mat

apexi turbo timer

sparco boost guage

tacho does not work

sound:

very good pineer head unit

new pioneer front splits

j-car rear splits

jbl 12" sub

j-car monoblock amp

exterior:

HID low beams

white led packers

window visors

roof wing

latle model chrome grill

17" work rims 8" front 9" rear. (paint on wheels pealing, need referb)

also have a set of stock 16" r33 wheels, depending on price will judge what will be on the car.

clear front indicators (not pictured)

autech side skirts (not pictured)

rolled rear guards

few bad points:

mainifold to turbo gaskit leaking a little

bonnet is a bit demaged with dints and paint flacking

rear qtr has a few small dints (about 5 of them the size or a 10 cent coin)

open to offers or possably swaps with cash my way depending on my circumstances as their currently constantly evolving. 17 inch wheels may not come with the car to drop the price a bit more depending on buyer.

any questions call Josef on 0431 625 850

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...