Jump to content
SAU Community

Recommended Posts

So I need suggestions on HSD and BC coilovers. Been told by many that these are out of the best coilovers to buy, so, just wondering what are people's thoughts/experiences with these.

Also, for the fitment on R34s, I've been told by a couple of people that it's much more difficult than doing it for a 32/33, and that you have to remove the rear seats an parcel shelf.. Whose done it before themselves?

Just wondering what's the difference, very curious!

They are easy enough to do, the rear seats and parcel shelf are pretty straight forward.

In terms of sourcing them, street to track sell the BC BR for $1165 delivered.

I have a set of tein for sale too, PM of your interested. Fitment is easy mate, don't think it's a hard job :)

I am a firm believer of spending more money on a quality set of coilovers (TEIN, Bilstein etc.) over the likes of a BC or an HSD. They ride better, handle better, are rebuildable, have better factory backed warranties etc.

As for fitting all Skylines are just as easy/difficult to fit and set up.

BC are rebuildable, they have a pretty good warranty from the looks of them.....

I currently have Teins but will remove and sell to someone that wants to rebuild the rears and have a nice set of coilovers. Of course the brands mentioned are cheap and arent going to win you any WTAC events but they are decent value for money, my reason for changing gets laughed at by all but its true, i dont want bright green and blue suspension as it just attracts defects, the fact the BC's are black are half the reason for choice :laugh: but its just less obvious.

I have driven cars with Tein (mine) and others with BC's and if they are set up right i find them to be similar.

It comes down to personal preference and use i guess :)

Doesn't sound difficult at all. Full been made to believe its a mission lmao.

$1165 delivered, that's a cheaper quote than I've been referred to elsewhere.

I'll definitely be checking it out.

Yeah I've just started looking at Bilstein and Tein actually, but I'm mostly looking for a cheap set that are a reasonable quality for now :)

Another brand to consider is Fortune Auto, built in the USA with a strong history in American World Time attack.

Coilovers that are built to order without the price tag of the more expensive brands.

I currently run them in my own R34.

Doesn't sound difficult at all. Full been made to believe its a mission lmao.

$1165 delivered, that's a cheaper quote than I've been referred to elsewhere.

I'll definitely be checking it out.

Yeah I've just started looking at Bilstein and Tein actually, but I'm mostly looking for a cheap set that are a reasonable quality for now :)

http://www.streettotrack.com/coiloversbcracing.htm

Email him and the price is normally a bit better depending on the AUD i guess :)

And no, its not a drama as long as you have some idea of how to operate tools..... Remember a wheel align after if you change height too!

Another brand to consider is Fortune Auto, built in the USA with a strong history in American World Time attack.

Coilovers that are built to order without the price tag of the more expensive brands.

I currently run them in my own R34.

great! I'll be looking into those, anything that is a reasonable quality/price is what I'll go for cause it's just my daily so don't need anything too fancy!

http://www.streettot...ersbcracing.htm

Email him and the price is normally a bit better depending on the AUD i guess :)

And no, its not a drama as long as you have some idea of how to operate tools..... Remember a wheel align after if you change height too!

I'll send him a message now & yep, got that covered!

Thanks for the help! :)

As for installation, it's not too much of a mission, but yes, you will have to take out your rear seats and maybe parcel shelf. Unless there is a way without, but I had to when I did mine, lol.

Parcel shelf coming off may just depend on your tools though, I couldn't get nice angle and strength in with ones I had, hence need for it to come off, but maybe you can get away without.

Edited by kaitoukid

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...