Jump to content
SAU Community

Recommended Posts

Apexi GT Spec Downpipe for R33 GTS-t

Model: 145-N004 9G8

  • Stainless Steel (needs a good polish for some bling brahh)
  • No dents
  • Comes with gearbox bracket
  • 80mm pipe diameter (3.15" inch)
  • I think it should Fit R32 GTS-t (please check before purchasing)
  • Comes with 2x nuts, 2x nuts, 1x exhaust gasket

Price: $150 (Will install for prospective buyer for slab of beer)

Decat Pipe/Cat Delete Pipe/Test Pipe/Defect Pipe/Flamezzzz Pipe lol

  • Mild Steel
  • Has provision to install a cover
  • Has temp sensor thread
  • Comes with 2x nuts, 2x bolts

Price: $50 (Will install for prospective buyer for slab of beer)

Location: Fairfield, NSW, 2165

Contact: PM or Reply here

Cheers,

Johnny

IMG_3326.jpg

IMG_3327.jpg

IMG_3328.jpg

Decat will fit:

C33/A31/S13/Z32/R32/R33/BNR34

Downpipe will fit:

R32/R33 most things running RB20DET

Sold:

Decat Pipe/Cat Delete Pipe/Test Pipe/Defect Pipe/Flamezzzz Pipe lol

Price: $50 (Will install for prospective buyer for slab of beer)

Still Available:

Apexi GT Spec Downpipe for R33 GTS-t

Model: 145-N004 9G8

Price: $150 (Will install for prospective buyer for slab of beer)

MONDAY (fking fail) TUESDAY bump :woot:

ALSO:

Stuff For FREE 1 [Here] - R33 ECU Passenger Kick Panel, Hand Brake Assembly & Main Cable

Stuff For FREE 2 [Here] - RB20DET Oil Cap, Oil Sump Plug, Hoses, CA18DET Hoses

Stuff For FREE 3 [Here] - 180SX Interior Bits - Trim, Cargo Straps, Washer Bottle Parts, etc.

$120 SAU Special, bring a cold 6 pack and I'll fit it too :)

MONDAY BUMP MOFOS

I'M ALSO SERZ, I SELL THIS AND I'LL BECOME A SAU NSW MEMBER TOO lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah i have R34 with factory small box and now RB25DET NEO swapoed and iam planning to upgrade to big box.  So i would be good as long as i do not change diff? 
    • Based off what you’ve said here, I think I’ve figured out a good bit of what I’ve done wrong -  So on the line going from the PCV valve to carbon canister, there’s a T joint that is pretty much right next to that lower port - I hadn’t noticed that the hose in the diagram was curved to attach onto the carb, so I was putting that line for the lower port onto the PCV line / carbon canister line instead. I’m going to have a flick through the manual again tomorrow and should hopefully find a diagram that’ll show me where that T joint should be connected to. Timing also 100% needs to be sorted out as well, should be able to tackle that tomorrow as well. Definitely feel like I should be on the right track now though. 
    • The screw is for idle (pilot circuit) mixture adjustment. Else, I'm confused ~ the diagram shows 2 carby ports, and the intake manifold port, but you're suggesting the "2nd port on the back of the carb that isn’t mentioned in the diagrams" ...yet, both carby ports are shown...que?... ...in any event, that port should be connected, but if not (like it is now), it's unlikely to cause a backfire out the carby (it would introduce false air and give you a fast/lean idle) ...sounds more like timing issues/spark plug wire routing responsible for the backfiring.    
    • That's fair, I can see both points. I get enthusiastic when I see the FS section has a new post and want to see what interesting thing someone is selling. Then I get deflated it's a bump of a 10 year old post. Ha ha
×
×
  • Create New...