Jump to content
SAU Community

Recommended Posts

Pair-17x9+18

WEDS Professor mesh

Discontinued

have gutter rash and could use a polish on the dish

Come wrapped in 225/45/17 Federal RSR's ($400+ of tyre) that have only done 3 or 4 sessions drifting

Just clear R23/33 rear brakes, will need a 20-30mm spacer to fit on the front, but can fit under s14 guards with 3ish deg camber with a 30mm bolt on on the front

$850

6037252303_bdb061617c_b.jpg

IMAG0072.jpg

IMAG0044.jpg

425990_307111876004634_278229208892901_798571_565966680_n.jpg

Pair-17x9+20 equips,,,,, small lip 3ish cm

light rash/scratches. No tyres

$250 .... payed over $400 for these from japan

IMAG0356-1.jpg

Pair-17x10+30 meisters

10cm or so cm dish

Light rash... 1 has 10cm or so deep rash

Thrashed tyres

$750

IMAG0159.jpg

IMAG0577.jpg

IMAG0578.jpg

Speedy wheels

16x7+35??????????????????? no idea tbh

only 3 usuable, one I had to cut off the car :lol:

2 tyres just above indicators, the other 2 70+% 225/50or55/16

$50

IMAG0483.jpg

IMAG0482.jpg

R32 GTR passenger seat

Modded rail to bolt straight in to S chassis

1 cig burn, could use a steam clean

$200

IMAG0574.jpg

Stock S14 Kouki tail lights

3 piece lights and garnish

The option/luxury type with the grey surrounds compared to the dark black

$300

40151_1578160007977_1054948418_31695964_6633882_n.jpg

IMAG0060.jpg

Stock s14 Parker lights

$70 for the pair

Located Campbelltown NSW

post at buyers expense

Link to comment
https://www.sau.com.au/forums/topic/410002-workweds-wheels-other-goodies/
Share on other sites

Bought a set of rims for my daily that have Yokohama's on the rear. There a waste on my car and a little to big so seeing if there is any interest.

They are Advan Sport in a 275/35/R18 and have a tread wear of 180.

These are USED, but still have 5mm of tread groove on the inner/cambered side and are not excessively camber worn.

The have scrub marks from the 10 min drive I did with them on the car as it fouls on the last 1mm of the inner lip as guards haven't been rolled yet. And If I lower the car they are to fat and sill prob scrub on the inner guards

These go for $300 a corner new.

Will only sell if someone is 100% on them and then I'll remove them. Otherwise I'll put them on the car after the guards are rolled and wait till there dead before putting new tyres on and lowering.

IMG_5431.jpg

IMG_5432.jpg

IMG_5433.jpg

Fronts are bald on inner edged (and 245's) so not worth keeping

so $120 for the rear pair with decent tread

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...