Jump to content
SAU Community

Recommended Posts

hi guys, my dad recently got his hands on an OS Giken Flywheel, and twin plate 5 puck solid center clutch that came out of a c34. it needs new clutch plates, but seeing as though he rebuilds clutches they are worth next to nothing, and the clutch/flywheel/rebuild will cost me nothing as he wil do it... should i change up from a stock clutch.i know the gear changes will be more harsh, and might be a bit of a rougher ride, but im not using the stag as my daily anymore, so its not a big issue.

opinions? anyone else got a solid 5 puck twin plate that can comment on driveability?

cheers.

Depends what your going to use the clutch and car for? I would say no unless it's a hardcore car. There was a thread recently where someone purchased a car with one of these and swapped it out for a less harsh setup.... Would be a tough bit of gear but all depends on its use

thats what i was thinking, i just sold my toy car(r33) to scale down in power, and im only doing very mild mods to the stagea... aiming around the 260rwkw mark. i was personally thinking about putting in an NPC organic single, which was suggested by someone else, but seeing as though this clutch was sitting there in my old mans shop it was worth contemplating. im not to sure about the clutch itself or if its possible but i could have some custom sprung center plates made up, my old man has done me custom clutches in the past, i guess id have to talk to him, clutches really arent my thing lol, just like performance jap engines arent his haha, he is a holden man through and through.

I think your better off doing both, fixing the current twin plate and selling it to someone that will use and abuse and just get yourself the NPC and maintain the drivability and enjoy your car..... Personal opinion only :)

Mr NPC coming in again.

mat is right on the money. sell it and get a more driveable clutch

I will start taking your commission as i am all over this!

A twin-plate has its advantages (like a lighter pedal feel compared to a single of similar power handling capabilities), but if you want a twin-plate, go for a full-face one. I just recently replaced an Exedy single plate (was supposed to be a heavy duty) with a Nismo Super Coppermix twin, and the Nismo is so much nicer to drive with!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
    • EMU Classic. For what I need it to do I see no reason to upgrade. Link and Haltech would both cost an extra chunk of money for a lot of unutilized features
×
×
  • Create New...