Jump to content
SAU Community

Recommended Posts

FOR SALE: 1993 sr20det red top manual

$6000 ono

Rebuilt motor, new rings, gaskets, and bearings approx 20k kms.

Walbro fuel pump 500hp

New windscreen

New brake pads front

New z32 fuel filter

Pioneer 6 x9’s in parcel shelf

Aftermarket head unit

New sway bar link bushes

New injector seals

GKtech steering lock spacers

brand new exedy lightened flywheel

brand new exedy Heavy duty button clutch

Brand new clutch master cyl

3 inch exhuast (GKtech dump + front pipe, 3 inch high flow cat, custom cat back and twin pipes)

cusco coilovers (front only) height/camber adjustable

Twin thermo fans with digital controller

Apexi Pod filter

welded in rear strut brace

Whiteline Front strut brace

subframe locking collars

custom 1 piece driveshaft

Non hicas rear subframe

LSD diff

Car has good power and handles well. Car was used as a daily until I upgraded to an r34, serviced every 4-5k with quality oils and filters.

Body is a bit rough in a few spots, nothing out of the norm for a 180.

Drifteks in picture will NOT be included, some spare wheels will be provided.

REG included till March 2013. No rwc.

$6000 ono

Contact Josh via msg / call on zero-four-13 103 645

post-85528-0-64939900-1350101597_thumb.jpg

post-85528-0-75999500-1350101620_thumb.jpg

Edited by fyjosh

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
×
×
  • Create New...