Jump to content
SAU Community

Recommended Posts

Hi all,

I noticed today that my skyline started blowing steam out of the exhaust and I mean alot of steam (not from exhaust condensation) any ideas on what it could be I thinking maybe head gasket? I know the exhaust valve in piston #5 is not sealing properly which I am hoping to get fixed next week, I noticed this when I had a compression test done on the car.

Any info would greatly be appreciated

Thanks

James.

Link to comment
https://www.sau.com.au/forums/topic/411966-head-gasket/
Share on other sites

Get the coolant tested for combustion gases. Not a conclusive test, but could tell you more than we can tell you. But yes, it does sound like a head gasket. Or perhaps a crack, which may be the cause of your valve leakage too, if it is through the seat area. You might have a lot of damage in that head (cross yoru fingers). I'd be looknig around for a spare head in case it turns out to be worse than you hope.

Link to comment
https://www.sau.com.au/forums/topic/411966-head-gasket/#findComment-6587913
Share on other sites

If you believe you're getting steam due to blown HG, it means water in cylinder. Get some pressure in your cooling system (ideally using a pressure tester), remove all spark plugs and let it sit for a while (ie come back in an hour). Check all piston crowns for coolant seepage, crank engine over while looking for coolant emission from spark plug holes.

Generally if its bad enough you'll notice a miss after the car's been sitting for a while, as coolant leaks into cylinder. The miss will clear after a few seconds usually, as the water clears.

Link to comment
https://www.sau.com.au/forums/topic/411966-head-gasket/#findComment-6588709
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
×
×
  • Create New...