Jump to content
SAU Community

Recommended Posts

Just did the ECU reset, made a huge difference

1st gear now holds all the way to 6500rpm at WOT and chirps into 2nd rather than short shifting at 6000rpm like it was before

When cruising at 100kph in D mode and then giving the car WOT before the reset the car would pick up the revs by about 500 for a second or so and then thump into 3rd gear. I still get the second or so delay but now it changes down to 3rd without the thump most of the time

Much happier now

I would take it back and have matic J put in the box, to many horror stories for me to think about using something other then that in the box.

Edited by T4NK

http://www.clubfrontier.org/forums/f8/truth-about-matic-j-55979/

Taken from the above link

i saw yet another post about someone being a little nervous about switching to something other than nissan fluid in their auto tranny on a 05+ frontier and i think that for alot of people here nissan atf is a touchy subject and i want to try and eliminate everyone's fears of using something other than nissan fluid or atleast give you a little more knowledge about what it is your putting into your tranny. For starters matic j, this fluid is a semi synthetic JASO 1A spec ATF actually made by "]Castrol and sold to nissan who then puts their name on it and slaps all the dire warnings on everything in their vehicles about it but the fluid is nothing more than"]Castrol Transmax J which castrol made to work in all JASO 1A spec Japanese auto trannys. JASO 1A spec is the main Japanese standard for ATF and this castrol fluid is used by nissan and subaru and is good for use in Toyota T-IV and Type T fluid requiring transmissions. This fluid has also been approved for use in applications that call for Allison C4, Dexron III, and Mercon. Castrol TransmaxJ Product Data Sheet

Some more JASO 1A spec equivalents to this fluid are Pennzoil ATF-J and IDEMITSU ATF HP which is the fluid used in Japan for our trannys

There are also plenty of Universal ATFs that can be used and what makes these so universal is that they are actually just fully synthetic ATFs that are made to JASO 1A spec which you have see above that JASO 1A spec fluids have been aproved for use in Dexron III, Mercon, Allison, and is suitable in toyota t-IV and type T along with many other trannys from many other companies. The Japanese standard of JASO 1A spec actually far exceeds the standards of most other ATFs that manufactures require for their trannys which pretty much makes anything that is made up to JASO 1A spec a universal ATF so don't let yourself get turned off when you go to amsoil's website and look at the Universal ATF and see a massive list of compatible applications, when you look at this list and wonder "how does this fluid work in all these applications" its because the Japanese standard of JASO 1A spec is far superior to fluids of any of these other applications to date. once again the best of the best comes from japan! There are however some applications that JASO 1A spec fluids do not work in and most Universal ATFs are not recommended in or have not been fully tested in like Ford Type-F, Dexron VI, and any CVT tranny

a few universal ATFs that you can breath easy about switching to now are Amsoil ATF, Motul ATF-1A, Mobile 1 Synthetic ATF, Amalie Universal Synthetic ATF to just name off a few that i can think of off the top of my head.

i hope this little write up will help shed some light on the somewhat touchy subject of ATF and maybe help any of you that are kind of on the fence make a decision about what you which to run when the time comes for tranny service on your 5 speed auto frontier. Thanks for Reading

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • also possibly backed up to my filler and shat down it! 🤣
    • Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
    • What sold me on Trailer Park Boys is this scene: Great stuff, just stay clear from the new Netflix production.
×
×
  • Create New...