Jump to content
SAU Community

Recommended Posts

i went and bought what was said to be an r33 gtr skyline but according to the chassis plate it was produced on the 9th month of 1993. from what i have gathered they didnt release the r33 gtr until 1995 yet this has the full gtr body, interior and running gear including rb26dett and 4 wheel drive. the plate also states that it is an rb25det and it says ecr33, it has got me stumped and i am really hoping i havent been ripped off. i couldnt imagine somebody could justify the costs involved with going to such an extent to mock up a gtr.

Link to comment
https://www.sau.com.au/forums/topic/412928-can-someone-give-me-some-info/
Share on other sites

If you wanna give me your Vin, I can check it in NISSAN FAST and see what it says.

Although, if it says ECR33 & RB25det, this may be all you need to know.

Edited by Not a Pulsar

Dude if the build plate says it's an ECR33, you've been ripped off. What's more, the good bits inside your car were probably stripped from a stolen one, so you'd want to be checking your engine number quick smart.

  • 2 weeks later...

Yeh mate tell one of the boys your vin so they can run it in the Nissan fast programme which will distinguish what car it is.

Look up 'get vin fasted' or similar

From what youve described, you've got yourself a 33 gtr that's got 33 gtst build plates and can only be rego'd as such.

A good way to check right now is have a look at the Japan vin that's stamped into the fire wall and see how it compares to the blue build plate. If its different your've got ya self in a jam.

Good luck mate.

Edited by badben

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
    • It's TWO steering wheels actually. 😛 one for each hand They are wheels, and they steer!
×
×
  • Create New...