Jump to content
SAU Community

Recommended Posts

Model: R32 Skyline GTR

Year: 1993

mileage: 113000kms

Colour: Burgundy

Price: $26,000 ono

Reason for sale: Changing to an s2000.

This is my beloved R32 GTR. I bought the car pretty much as it is from a mid aged car lover 6 months ago. This car is pretty much a street registered track car. Good for track days and other kinds of racing events. Also pretty good to drive on the street if you can put up with the clutch and consumption of petrol. Condition of the car is really good for its age. interior i dare to say is 1 of the best in r32 out there! Chassis is 100% straight with no rust at all. couple of panels have been repainted but still in good condition, not faded or scratched except the front guard on the driver's side has tiny bit of scratch.

AC has been completely taken out. And the only really flaw of the car is the dash lights were blue when i bought the car and now they are out.

Heres the list of mods:

Engine:

- Garrett 2860-5 turbos

- HKS cams and camgears

- HKS headers, factory dump pipes with nismo front pipes and cat back system

- Nismo 600cc injectors with nismo fuel pump

- Splitfire coil packs

- Oil cooler, Trust oil sump, oil restrictors.

- Alloy radiator

- Carbon fibre airbox

- Custom made oil catch can by Silverwater Automotive

- Silicon radiator hoses

Drivetrain:

- Extreme twin plate clutch

Electronics:

- Apexi Power FC with hand controller

- HKS boost controller

- Blitz turbo timer

Suspension:

- Bilstein coilovers

- Nismo strut brace

Brakes:

- Large 2 piece front brake rotors

- Slotted rear brake rotors

Interior:

- Very rear Nismo optional seats!

Those are the mods I can think of on the top of my head so far. Car is currently running on 1.1bar(low) and 1.3bar(high) boost. I normally run it at high boost and never had a single problem. Knocking is always at around 35. Highest was seen at 42 for a split sec. Personally I have never dynoed this car so I can't tell you how much power it makes. It was tuned by last owner but I will tell you it is faster than my friends 300awkw Evo and from 80-170 in about 6 sec and feels a lot quicker than my last 300awkw r34 gtr so I'd say it is around 330awkw if not any more.

Now here is photos:

244091_10151075163656121_755776144_o.jpg

277350_10151075164821121_2082710821_o.jpg

471058_10151081578316121_1762987622_o.jpg

55323_10151075167551121_1268359631_o.jpg

534743_10151132584991121_1131059316_n.jpg

Edited by G0Z1LLAAAAA34
  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/413131-syd-1993-r32-gtr-for-sale/
Share on other sites

Forgot to mention that the car also has Attesa AWD switch, Nismo N1 head lights and LED taillights. Will post a photo of the full dash this weekend. Dash has absolutely no bubbles on it!.

Edited by G0Z1LLAAAAA34

K guys, Due to my personal circumstances, I need this car gone so here is another big price drop, $21000. I am very negotiable on this price as I need it gone. So please throw me your offers. My number is 0413 205 603. Rego ends in Jan.

  • 2 weeks later...
  • 3 weeks later...
  • 3 weeks later...
  • 1 month later...
  • 3 weeks later...
  • 4 weeks later...
  • 9 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...