Jump to content
SAU Community

Recommended Posts

hey guys and girls,

currently have to many r32 parts hanging around that need to be cleared.

i am located in South Australia (Adelaide Hills)

Happy to post smaller items at buyers expense.

1. R32 driver and passenger 'A' Pillar trims (gd condition, 1 really tiny hole in drivers side) $45 pair

post-60871-0-97760700-1352629242_thumb.jpg

post-60871-0-11718900-1352629108_thumb.jpg

2. Clutch Master Cylinder (gd condition, no leaks) $45

post-60871-0-84718000-1352629544_thumb.jpg

3. Boot Plastic $10

post-60871-0-80785400-1352629453_thumb.jpg

4. R32 dash (has a couple minor cracks up by top a/c vent, perfect for drift) $45

post-60871-0-57997900-1352629669_thumb.jpg

post-60871-0-77348200-1352629772_thumb.jpg

5. A/c controller (gd condition, working when pulled out of car) $45

post-60871-0-95224800-1352629870_thumb.jpg

6.Centre dash trim (no holes, tears etc) $25

post-60871-0-30135600-1352629974_thumb.jpg

7. R32 Overflow bottle (no cracks or leaks) $45

post-60871-0-49023700-1352630079_thumb.jpg

8. Drivers side inner plastic guard (wear marks, small slit) $35

post-60871-0-88460100-1352630222_thumb.jpg

9. Manual rubber gear stick boot $20

post-60871-0-15500100-1352630376_thumb.jpg

10. Cusco Solid Rear Cradle Bushes (gd condition) $ 55

post-60871-0-29101200-1352630534_thumb.jpg

11. R32 2 door 1/4 windows $75 ea (have LH and RH)

post-60871-0-22350000-1352630695_thumb.jpg

post-60871-0-76232200-1352630815_thumb.jpg

12. Brake, Clutch and Acc pedals (gd condition, have foot rubbers) $45 each

post-60871-0-42314200-1352631051_thumb.jpg

13. R32 2 door scuff panels $20

post-60871-0-50129400-1352631343_thumb.jpg

14. R32 rear parcel shelf (covered in carpet, made strong, speaker holes) $35

post-60871-0-90468400-1352631483_thumb.jpg

15. R32 turbo rear brake calipers (no leaks) $125

post-60871-0-06243500-1352631619_thumb.jpg

16. R32 set of 4 seat belts (no fraying/tears, rear belts have buckles) $75

post-60871-0-44413300-1352631719_thumb.jpg

17. Clutch slave cylinder (no leaks) $25

post-60871-0-05503200-1352631846_thumb.jpg

18. Steering wheel plastics (no holes, mint condition) $35

post-60871-0-00743700-1352631968_thumb.jpg

19. R32 gtst rear tail lights (gd conditon, slight wear mark on rhs light, minimal) $125

post-60871-0-31958800-1352632129_thumb.jpg

post-60871-0-50222800-1352632271_thumb.jpg

20. R32 rear quarter interior side panels. (mint condition) $45 each (have LH and RH)

post-60871-0-27763000-1352632419_thumb.jpg

21. R32 2 door side skirts - Type M i believe (gd condition) $125

post-60871-0-95464200-1352632580_thumb.jpg

22. R32 washer Bottle (no leaks or cracks, comes with motors) $50

post-60871-0-26363100-1352632725_thumb.jpg

Thanks for looking

Have plenty of R32 2 door parts around, so if u are after anything hit me up and i can see what i have.

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • It's been quite the ordeal but hey, at least you figured it out.
    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...