Jump to content
SAU Community

Recommended Posts

Selling all the NEO parts i have that i no longer need.

Located in SA. Postage at buyers expense. PM me.

NEO / R34 RB26 CAS - $100

PB180393.jpg

NEO Coil Pack Loom, Good condition - $80

PB180394.jpg

NEO Coil Packs, 40,000kms, Good condition - $200

PB180395.jpg

S2 RB25 Throttle body (clean) - $50

PB180396.jpg

NEO Plenum, bare, sand blasted - $60

PB180397.jpg

NEO Injector Loom - $60

PB180398.jpg

NEO IAC Block, sand blasted - $70

PB180399.jpg

NEO Trac Control Throttle body - $60

PB180400.jpg

S2 RB25 / NEO AFM - $100

PB180402.jpg

NEO Injectors, Been in plastic bag since removed from engine - $100

PB180403.jpg

NEO Boost Sensor - $100

PB180406.jpg

NEO Engine cover - $50

PB180407.jpg

Brand New NEO Harmonic Balancer - $280 ($340 new from KMS)

PB180409.jpg

Brand New Clutch Fan Suit RB's - $170

PB180411.jpg

NEO Water Hoses (Brand New) - Doesn't Include All but a lot of them - $160 (Were $250 odd from Nissan)

PB180410.jpg

- Front bleed valve to thermostat housing - 14056-AA500

- Rear bleed valve to rear block t piece - 14056-AA510

- Rear bleed valve to throttle body - 14056-AA505

- Rear bleed valve to runners - 14056-AA515

- Front bleed valve to runners - 14056-AA520

Tomei INLET Adjustable timing gear - $150 Including postage.

2012-08-10_16-38-20_4451.jpg

NEO Pistons and Rods - $100 good nic - Rods are the same as RB26 rods

P6110304.jpg

Link to comment
https://www.sau.com.au/forums/topic/414069-rb25-neo-parts-for-sale/
Share on other sites

  • 2 weeks later...

Have you worked out if you need it?

Sorry for the late reply. I honestly havn't worked it out if i need it or not.

Do you know the precise reason for it? I know it controls the valve for the purge canister. But why did the NEO have this ECU controlled solenoid valve and all other RB's did not?

Bump btw.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
    • yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
×
×
  • Create New...