Jump to content
SAU Community

R33 Bits And Pieces

skylinekido
 Share

Recommended Posts

skylinekido Enthusiast

skylinekido

Posted
Posted

Hi all i have a few R33 bits and pieces just lying around and would like to clear some space

center console :$50

post-54702-0-38683700-1353824592_thumb.png

series 1 drivers seat ready to bolt in :$80 (can not post)

post-54702-0-89525700-1353825500_thumb.jpgpost-54702-0-61711500-1353825572_thumb.jpg

x4 19inch rims fronts are 19x8 and rears are 19x9.5 stud pattern 5x114.3

they have tyres 235/35 front and 275/30 rear nangkang tyres all round and in good condition

rims have some gutter rash: $200 (can not post)

post-54702-0-38865700-1353825126_thumb.png

series 1 front bar: $100 (can not post)

post-54702-0-96652300-1353825188_thumb.png

series 2 front guard LH: $70 (can not post)

post-54702-0-20144200-1353825259_thumb.png

NA series 2 front guard RH: $70 (can not post)

post-54702-0-03316300-1353825227_thumb.png

X2 series 1 head lights: $100 for the pair

post-54702-0-91063200-1353825324_thumb.png

dash surround: $40

post-54702-0-26630600-1353825383_thumb.png

Series 1 bonnet in good condition: $120 (can not post

post-54702-0-66798200-1353825447_thumb.jpg

x2 rear koni shocks: $70

post-54702-0-54191600-1353825674_thumb.jpgpost-54702-0-65438600-1353825723_thumb.jpg

all prices are Ono and location is beverly hills 2209 and PM me if you have any questions

:thanks:

Link to comment
https://www.sau.com.au/forums/topic/414388-r33-bits-and-pieces/
Share on other sites
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...