Jump to content
SAU Community

Recommended Posts

Hi All

I have the below for sale.

Everything works and in good Condition

Located: Inner West Sydney

Contact: 0430031987

-

Item1: GTR R32/R33 Apexi Power FC tuned & Z32 AFMS with Plugs (x2 sets of these)

Price: $1250 (will seperate)

Pics: http://www.ebay.com....984.m1586.l2649

-

Item 2: RB26 HKS 3" Front pipe

Price: $200

Pics: http://www.ebay.com....984.m1586.l2649

-

Item 3: Varex Cannon 3" Internal / 4.5" Tip with 2 remotes and wiring

Price: $250

Pics: http://www.ebay.com....984.m1586.l2649

-

Item 4: 3" 100 cell high flow cat and GTR cat back pipe

Price: $150 (will seperate)

Pics: http://cgi.ebay.com....em=190791762947

http://cgi.ebay.com....em=190791793092

-

Item 5: Rb26 flywheel balanced and machined 32 33 GTR

Price: $200

Pics: http://www.ebay.com....984.m1586.l2649

-

Item 6: RB26 Mild Steel 3" Front pipe

Price: $100

Pics: http://www.ebay.com....984.m1586.l2649

-

Item 7: JJR Type RS Style BOV x2 New

Price: $100 each or both for $180

Pics: http://justjap.com/s...&cat=296&page=1

-

Iteam 8: Blitz SS BOV x2

Price: $200 for both

Pics: Soon

-

Item 9: 100MM FMICblack

Price: $180

Pics: Soon

-

Item 10: Genuine Nissan head Gaskets RB26 (x2)

Price: $50 each

Pics: Its a head gasket...

Item 11: RB26 O2 Sensors x2 with dumpies adapters (came off 32 GTR)

Price: $150 for both

Pics: Soon

Edited by thegame-01

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...