Jump to content
SAU Community

Recommended Posts

Hey guys,

Just a few bits I have laying around with no use.

Genuine Z32 AFM done only about 5000kms - $250 (no plug)

Genuine Walbro 255lph suit Nissans done about 7000kms - $50

R33 S2 ECU w/ Nistune installed, done by Toshi on forums - $400

Stock 370cc RB25 Side feed Injectors (x6) - $50

R33 S2 Crank angle sensor (silver type) - $100

All parts removed only due to upgrade, all on running vehicle when removed, Located in Sydney. Can post if need be. Reason why I didn't post pics is because they're all in top nick with no damages, nothing to see lols.

as requested by some. all genuine................lol

post-40593-0-36973900-1360746499_thumb.jpg

post-40593-0-28074900-1360746572_thumb.jpg

all parts off r33 s2

Can throw in apexi podwith z32 for $25

Edited by OoskylineoO

just FYI guys for those who asked, ECU is tuned for a GCG OP6 high flow, stock injectors, Z32, pod filter, walbro 255, 3'' turbo back exhaust and 18psi - ~250rwkw.

PMs replied.

FUEL PUMP SOLD..

NEW PART ADDED:

GREDDY INFORMETER TOUCH - $450 posted anywhere in AUS, practically still new, only used for about 5months. Was on a R33 s2 (stock ecu), literally plug and play, plugs into consult port under driver side dash and gets it power source there as well. Useful unit to monitor engine activities, only removed due to upgrading to haltech ecu which was not compatible.

link to part:

http://greddy.com/products/electronics/informeter/filter:make:Informeter-TOUCH/

post-40593-0-78872900-1361343824_thumb.jpg

ECU no longer for sale, was mis informed about its compatability, does not have a Z32/R32 board. (basically a stock ecu with the chip changed) sorry guys.

Edited by OoskylineoO
  • 2 weeks later...

bump

$280 for z32 with new greddy plug and ill throw in the apexi pod!!

$350 for infometer touch shipped!! won't find it cheaper!

  • 2 weeks later...
  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, i’m making a rb25det coil loom for Vag short coil. Can anybody tell me which Ecu signal wire belong to coil number 1 and 2,3,4,5,6? The connecting switch in above pic is 8 wire i think white is for +12v and black for earth.
    • Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
×
×
  • Create New...