Jump to content
SAU Community

Recommended Posts

Hey guys,

Just a few bits I have laying around with no use.

Genuine Z32 AFM done only about 5000kms - $250 (no plug)

Genuine Walbro 255lph suit Nissans done about 7000kms - $50

R33 S2 ECU w/ Nistune installed, done by Toshi on forums - $400

Stock 370cc RB25 Side feed Injectors (x6) - $50

R33 S2 Crank angle sensor (silver type) - $100

All parts removed only due to upgrade, all on running vehicle when removed, Located in Sydney. Can post if need be. Reason why I didn't post pics is because they're all in top nick with no damages, nothing to see lols.

as requested by some. all genuine................lol

post-40593-0-36973900-1360746499_thumb.jpg

post-40593-0-28074900-1360746572_thumb.jpg

all parts off r33 s2

Can throw in apexi podwith z32 for $25

Edited by OoskylineoO

just FYI guys for those who asked, ECU is tuned for a GCG OP6 high flow, stock injectors, Z32, pod filter, walbro 255, 3'' turbo back exhaust and 18psi - ~250rwkw.

PMs replied.

FUEL PUMP SOLD..

NEW PART ADDED:

GREDDY INFORMETER TOUCH - $450 posted anywhere in AUS, practically still new, only used for about 5months. Was on a R33 s2 (stock ecu), literally plug and play, plugs into consult port under driver side dash and gets it power source there as well. Useful unit to monitor engine activities, only removed due to upgrading to haltech ecu which was not compatible.

link to part:

http://greddy.com/products/electronics/informeter/filter:make:Informeter-TOUCH/

post-40593-0-78872900-1361343824_thumb.jpg

ECU no longer for sale, was mis informed about its compatability, does not have a Z32/R32 board. (basically a stock ecu with the chip changed) sorry guys.

Edited by OoskylineoO
  • 2 weeks later...

bump

$280 for z32 with new greddy plug and ill throw in the apexi pod!!

$350 for infometer touch shipped!! won't find it cheaper!

  • 2 weeks later...
  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Was going to say the car pulls up nicely everywhere, especially going into that last long right hander before the main straight. Looks like a lot of fun.
    • Hey Dave, welcome aboard! Good to see another soon-to-be Stagea owner here. The wagons are awesome — plenty of space, still got that Skyline DNA, and loads of potential if you’re into mods. Definitely post up pics when you get it, everyone here loves seeing new builds. What model/year are you looking at?
    • See if you can thermal epoxy a heatsink or two onto it?
    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
×
×
  • Create New...