Jump to content
SAU Community

Bits N Pieces=R33 Gtst, R31, Rb30, 100Mm Cooler

SLY-25T
 Share

Recommended Posts

SLY-25T Mentor

SLY-25T

Posted
Posted

Hey All,

So I was gonna go down 25/30 route with the 33 but have decided I'd rather save to buy a house then spend my deposit on the car.

I only purchased the motor and cooler around 6 months ago and since then they have been sitting in my garage awaiting some love and attention.

All items are located in Wattle Grove, Sydney. Near Liverpool. Best contact is mobile SMS- 0401613535.

Not delivering at this time as I honestly CBF and just want it gone without hassles. Cash pickup much preffered.

1. RB30 Head and Block. Out of a R31 as can be seen by NISSAN stamps not HOLDEN. Unknown KM, only bought it to get sent away and get the works done.

$200

post-53838-0-79217500-1361235691_thumb.png post-53838-0-19006200-1361235711_thumb.pngpost-53838-0-00428100-1361235725_thumb.png

2. 600x300x100mm Intercooler with piping to suit Forward facing plenum with high mount on an RB30. Has attachment for water/meth (previous owner explained). Think the piping is to suit MAFLESS too.

$200

post-53838-0-91244900-1361236032_thumb.png post-53838-0-06324200-1361236065_thumb.png

3. RB30 Intake and Exhaust Manifolds. As previously stated, NISSAN not HOLDEN. As far as i know all the hoses are there on the intake. Only thing that should be needed is new gaskets? If I have no interest they will just be binned.

$50 for both?

post-53838-0-97340800-1361236208_thumb.png post-53838-0-14371600-1361236223_thumb.png post-53838-0-15401100-1361236235_thumb.png

4. R33 GTST HICAS unit. Was working in my car, replaced with a lockbar. As above, if no interest I'll just be throwing it out.

$50

post-53838-0-05217200-1361236356_thumb.png

5. RB25DET S1 Coil Pack cover. Prob good if you wanna muck around painting or cutting and customising.

$20

post-53838-0-14296700-1361236456_thumb.png

6. R33 GTST S1 rear strut brace. Just Jap brand. Looks to be a lil twisted but i was still able to fit it. Had alot of fuel pump issues so had enough of constantly having to take it off and back on.

$30

post-53838-0-31200000-1361236564_thumb.png

7. Excedy Heavy Duty clutch to suit R33 GTST S1 (Push?) worn out. Suit rebuild, was looking at sending away to rebuild but a clutch came up cheap.

$150?

post-53838-0-11436300-1361236675_thumb.png

As metioned, I'm not willing to post atm. Rather it get picked up and clear out my garage.

Best contact is by mobile SMS.

If most parts arent sold they will most likely be thrown out.

Throw me some offers.

Thanks,

Jaye

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      RB25DE NEO with Haltech ECU

      By Kinkstaah · Posted

      For fuelling the Haltechs have O2WB fuel controllers. Very useful for helping tuning VE and correcting for *small* mistakes. Of course if your injector/cam/trigger/sensor data is just wrong (or for a GTT which is not a GT) then you will get impossible reactions to things. I am sure you know this already but the reason people don't typically put haltechs (or any Aftermarket ECU) on GT's is because there's practically no real gains to be had - So this knowledge won't be commonplace.
    • ChriscoDom
      Rear Sway Bar Busshings - Holden Astra TS (2002)

      By ChriscoDom · Posted

      Can someone tell me if the cracks seen in the rear sway bar bushings in these photo's is unacceptable from a roadworthy point of view?  
    • GTSBoy
      RB25DE NEO with Haltech ECU

      By GTSBoy · Posted

      Shouldn't need a "base map" for anything other than guidance to ignition tuning. You just need the engine capacity right, the injector size right, and something, almost anything, for a VE map. On an NA engine, fuelling is almost completely a function of load signal & rpm. It should run and drive with a completely flat fuel map. It will be too lean under load, but that's easily fixed. We used to tune all ECUs without any base map. There were no such things (until someone had tuned a near stock engine on one, and then they had a "base map".
    • Kinkstaah
      Duncan's V37.......race car?

      By Kinkstaah · Posted

      What did you actually buy/how much did it cost? When I got mine in like.. 2017...? 2019? the aim was to run Torque for gauges via ODB2 and things like Track Addict/Laptimers/Dashcam/Reversecam/Spotify etc. Mine never broke, but I wonder if you've got the same needs (it sounds like it). Cause I liked the idea of being able to do anything with it. That said, yours also cost 3x the cost of what I spent so... food for thought.  
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      For me there is a massive difference in manufacturer or big brand crippled android (Sony, Kenwood etc) vs the sort of thing I've installed here, which is basically just a tablet in DIN form factor with open Android, and the other model of course is mirroring - Android Auto/Carplay. I hate the locked down manufacturer and AA options where they decide what apps I'm allowed to install, including the Launcher but also importantly things like Ecutek (for this car) or Real Dash (Stagea) are not supported. Plus those crippled versions tend to be slower due to both overheads and lower spec hardware. On the other hand, when this breaks I'll likely be in trouble for support....but how is that different to owning an Infiniti anyway
×
×
  • Create New...