Jump to content
SAU Community

Recommended Posts

'A tune' is not a fixed thing... so it's hard to shop a price for 'a tune'.

Nick at GT is good at what he dose and depending on how much time he spends doing what with your car will depend on what he charges you... it's not very common that a car will roll into his workshop with zero issues/problems etc and only needs 'a tune'.

Just go have a chatt with him, do as much of the preperation work your self as you can and book it in.

Cheers

Justin

Mainly I just need an idle and boost spiking fix as the person who tuned my car struggled with those 2 things as he usually only does power fc's. I didn't have the problems before the tune so I am guessing it's in the tune. Thank you Justin :)

They're usually the two most time consuming things to get right... Idle issues could be almost anything and as for boost, I'd just install a turbotech boost T and solve all your issues all at once.



What else did you change before the haltech install and initial tune? I'd be looking at pressure testing your intake and looking for leakes/split hoses and or missing vac lines.... clean your iac motor etc and making sure your intake is all sealed up properly.



What's the idel doing?




Cheers



Justin


The initial tune didn't have those problems, this is the second haltech tune but by a different guy.

The idle is just dying (mainly if you put the clutch in at 3k+ revs) and will stall at times or come very close.

The changes from initial haltech tune to this one:

850cc injectors

garrett 3076r turbo (with custom stainless intake)

bosch 040 pump

nismo fuel pressure regulator

I had heard boost T's were prone to boost spiking, is this just a myth?

Beau, in honesty you have changed alot between tunes.. you will probably find that your idle issues are as much mechanical in nature as anything else. Do you still have your stock bov? is it plumbed in as standard? are you getting reverb back through the new intake causing map sensor spikes, is your tps set correctly?

Nick can fix it for you, just don't expect a tune will be the solution... sounds like the tune needs a good looking over though.

A turbo tech boost T is as reliable as you can get.... just don't buy any other type/brand of T. Again, Nich has them on the shelf.

Cheers

Justin

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...