Jump to content
SAU Community

Recommended Posts

HI ALL,

I will be the owner of a GTR '33 v-spec soon and I would like some further help with HICAS from knowledgable peeps with past experience.I have read most of the topic post from the past but most were 2003/4 posts and i'm sure things are different now with the aftermarket products and easy fixes available.

Firstly what are the porblems HICAS can cause? :wacko:

and what are the advantages/ disadvantages with or without it ?

Secondly what eliminator kits are available now and cost roughly?

who can fit them or easy to do yourself?

I live on brisy northside and will be looking for a tuner/mechanic with extensive knowledge of RB engines and GTR's preferably that aint guna rip ya off if anyone can help with that also?

I have been quoted roughly $1200 for a HICAS eliminator kit, which i thought "shit that must be the best of the best" considering i had seen the tomei ones in past posts for $295,

but are the tomei ones a lifetime fix or a get by till ya can afford the best of the best lifetime fix?

also unplugging the electronic motor behind the diff, is this a quickfix or a permanent solution?

and does this create dramas with a straight driveline on the rear tyres with regards to toe in/out?

Please help one confused mutha#%&$er!!!! Thank you in advance!!

Edited by smidy

tomei kit doesn't replace the hicas bar, it just uses some brass discs to lock the bar into place and then electronically bypasses the hicas computer. If you're ball joints are stuffed (often more of a problem) then it won't help much either. It's a bit harder to unstick the rear with the hicas still working, having it locked out should help the rear be more consistent and predictable in oversteer, (helpful for balance on a race track). Probably there are better ways to initially spend your money, like quality tyres, good alignment, etc see how you go from there.

If you're looking for a tuner/mechanic northside go have a chat to Trent at Mercury Motorsport, they do a few RB's/GTR's there from time to time.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...