Jump to content
SAU Community

R34 Nismo Front Bar And Fmic Fit

DaHyp3

By DaHyp3,
in Exterior & Interior Styling

 Share

Recommended Posts

DaHyp3 Apprentice

DaHyp3

Posted
Posted

So I am going to be fitting a blitz return flow front mount to my ER34 which has a nismo front bar. I am not worried about the actual fitment of the cooler but rather how it will look and am wondering what other people with the same bar have done. Did the number plate need to be moved? Where and how did you mount the number plate? Can anyone post some pics of 34's with the nismo bar and a fmic.

Link to comment
https://www.sau.com.au/forums/topic/422824-r34-nismo-front-bar-and-fmic-fit/
Share on other sites
RusH_ Veteran

RusH_

Posted
Posted

I'm going to go ahead and say that the number plate probably wont need relocating at all, it'll be simply a matter of trimming off some of the back sections of the front bar to fit the cooler and piping. But how much is going to be up to you to figure out when test fitting the front bar,
There is a great tutorial on how to fit return flow FMIC's in the Tutorial section, have a look, i'd say it'll answer all of your questions.

DaHyp3 Apprentice

DaHyp3

Posted
  • Author
Posted

Hey RusH, yer have read the DIY and it is great. I'm not worried about trimming behind the bar, doesn't look too hard to do. I'm more worried about how it will look and making sure the cooler actually gets plenty of fresh air. I was thinking of making a Nismo template and spraying a logo on the cooler as well. So if anyone has done this any tips or advice would be great. The only reason I was thinking of moving the number plate is for more airflow to the cooler but tbh I think it would look quite ugly but when you look at a nismo front bar there doesn't look like a lot of surface area for air to flow through. I just wanna make sure fitting a cooler will not just look better but actually perform, otherwise it is just an expensive piece of bling.

RusH_ Veteran

RusH_

Posted
Posted

Fair enough,
One thing you could consider doing which i've done is redrilling the holes in your number plates and moving the plate upward, still positioned in the centre but just sitting higher up, this frees up the front end significantly depending on how high you take it.

DaHyp3 Apprentice

DaHyp3

Posted
  • Author
Posted

That's a great tip, dunno why I didn't think of that. Will move my number plate up a bit higher, problem solved I reckon. Would still like to hear from anyone that has spray painted a logo onto their cooler and how they went

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      boost source Size Garrett gt28 gen2

      By TurboTapin · Posted

      You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • QB6SAGR
      Battle of the broken skylines

      By QB6SAGR · Posted

      Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • cosline
      R32 gtr transmission strength, billet plate

      By cosline · Posted

      Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Rezz
      Spotted on the street....

      By Rezz · Posted

      Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...