Jump to content
SAU Community

Recommended Posts

For sale is my R33 GTST. Since getting a work car 4 years ago my skyline has sat under cover in the driveway and only done 1000k’s or so. With it costing reg and insurance it’s time to sell it up and move on to the next hobby.

The car has a strong, well maintained engine. It’s done 56K km since the rebuild (156K kms total on car). It did 600kms on the freeway each week for 2 and a half years so it’s been a pretty easy life given its power. I’ve had the car since 2003 so don’t really want to part with but have to cut my loses eventually.

Car info;

  • 156,000kms with current rego until August 2013.
  • Interior is in great condition except for 2 holes in the drivers A pillar from mounted gauges.
  • New leather break and gear boots.
  • Skyline floor mats in good condition.
  • Recaro seats with some standard wear on them.
  • Nizmo 300km/h dash cluster.
  • Short shift kit.
  • Impul light weight racing rims (17in white 5 spoke).
  • GTR rear spoiler / Veilside pods / skirts.
  • Full black coloured body with resprayed roof, boot and bonnet.
  • Turbo back exhaust; x-force dump-front pipe, x-force high flow cat, Blitz 3in catback.
  • Apexi intercooler.
  • Other extras that I may have forgotten to mention.

Engine info;

  • 273rwkw (with dyno sheet) useable power.
  • Power FC tuned rich for the motors longevity.
  • Ported & polished with angle cut valves.
  • Forged pistons.
  • GTR crank and rods.
  • Denso 740cc injectors.
  • Q45 Infinity AFM
  • Pod filter – could do with replacing
  • Turbo - Custom: Ball bearing: Equivalent to GT2876R? Compressor – A/R 0.70, HKS exhaust housing – A/R 0.64.
  • Greddy blow off valve.

For a RWC it would most likely need the following standard wear and tear items; new windscreen, front discs, potentially tires, clutch, the tacho is playing up (I was using a 4.5in tacho with shift light but took it out because it was a functional but a bit wanky). All of which I haven't spent the money on in case it gets.

$8,400neg for the car as is without RWC or Reg.

A tough looking car in great condition that gets plenty of comments. Well worth a look for and reasonably priced for what’s in it.

Willing to split the motor out for $3,900 (including everything under engine info) if the interest is there and part out the rest.

Thanks,

Adam

post-7819-0-89378100-1365067745_thumb.jpg

post-7819-0-32512700-1365067792_thumb.jpg

post-7819-0-96880000-1365067844_thumb.jpg

post-7819-0-88304300-1365068218_thumb.jpg

post-7819-0-63621400-1365068260_thumb.jpg

post-7819-0-92421100-1365068296_thumb.jpg

post-7819-0-88022400-1365068366_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
×
×
  • Create New...