Jump to content
SAU Community

Hello From The Uk

Scrappy doo

By Scrappy doo,
in Four door and wagon builds

 Share

Recommended Posts

Scrappy doo Newbie

Scrappy doo

Posted
Posted

Hi my name is luke and I'm from the UK.

There has always been a lot of talk of this forum in the UK so thought I would join up and see what it's all about.

I'm currently on 2 forums here in the UK, one has gone a bit quite due people tucking their skylines away until summer and the other I got ripped off on by a rep so I try not to use them.

I'm currently driving a black spec 1 r33 gtst, it was running just over 300bhp when I bought it. Since then I have done a few performance mods and I'm currently looking to get the map adjusted and get a couple of power runs done on the Dyno.

So there you have it. Hello everone

Link to comment
https://www.sau.com.au/forums/topic/423380-hello-from-the-uk/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Neil's R33 Gts-t Build

      By GTSBoy · Posted

      Starter motors used to use the weight of metal (magnets) to provide torque. Now they use (more) current instead. This. It's completely normal.
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      So thing that had me stumped, but I think is OK....is that when it was up in the air, in neutral I had it running to bleed to coolant while I put the wheels back on. I noticed the rears were turning (slowly) which I'd never seen before 20250928_163512.mp4     Because there had been an issue with clutch slip due to pedal adjustment on the dyno, I assumed there was still and issue so spent some quality time upside down under the dash adjusting the pedal....but no matter what I did the wheels still turned in neutral. Even disconnected the master cylinder to pedal rod and same. In despair, I even removed the clutch slave so there was no chance of any preload causing it.....still happened. So either: 1. Something is not right in the bellhousing, or 2. Its a thing sometimes with cold, thick gearbox oil Internet says it might be 2, I hope so!
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      OK, few more things sorted and it is ready for a shakedown on 10-Oct, with one weird thing. Changed the run in oil and filter for the good stuff. 8l came out, about 8.5 went in with filter so that looks all good. Changed the starter (again), this time for a brand new one, works good. Interesting that the Taaaarks one is shorter than factory but spins harder, I guess electronics have moved on a little in the last 30 years. Will be nice to have a bit of extra space under there. Put the timing cover back on, and noted where the cam gears were set as a record.  Will need to double check the timing but it is pretty close. Also put the coil pack cover and intake snorkel back on. Exhaust Inlet Changed the water out for coolant, bled up nicely. Removed the rear brake pads (well worn factory sumitomo ones!), gave the hardware a good clean and reassembled. I've put bendix XP on the back again because the price is excellent at $150 a set and they worked well on the V37. Front pads have plenty so no issue there
    • jez NF
      The Evolution Of "night Fury"

      By jez NF · Posted

    • r32-25t
      remote oil cooler hose size, 8,10 or an12?

      By r32-25t · Posted

      Mine is all -12, I’m running a dry sump in a billet block though 
×
×
  • Create New...