Jump to content
SAU Community

Recommended Posts

Hi guys For sale 2 x Genuine Garrett Gt28/71r's with Gt28 housings.

The 2 turbos originally had 3 inch GT30 style front comp covers But I had 2 S-15 gt28 housings machined to fit by Glen munro.

Front comp housing A/r .60

Rear Turbine housings are .82

T28 foot flange So will Bolt up to either SR20 or RB26 no issues

Dual ball bearing cores

Comes with Braided Oil Fittings, Oil Drain and water push-lock hose fittings not that it matters because these bolt up to stock fittings.

Comes with internal wastegate actuators. Comes with Dump pipes, gaskets, New studs, nuts and two gt28 turbo beanies

Turbos may require clocking/turning around as they were going to be used on a 2jz project but project no longer going to happen due to extremely harsh financial difficulties. everything is Brand new never used only fitted and then removed rear turbine housings have been painted with VHT exhaust Black to avoid rust/corrosion Front comp housings were painted VHT gloss enamel black to make them less noticeable in the engine bay. These can be easily bead blasted raw again 2jz adapters will be removed before sale

chasing $2500 for the both of them or $1250 each Firm 0428848963 or pm me Michael

turbo3a.jpg turbo2aq.jpg turbo1a.jpg turbo3b.jpg photoury.jpg 012v.JPG 013bwk.jpg 014yq.jpg 015bhk.jpg 016fw.jpg 017jqb.jpg 310vec.jpg

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...