Jump to content
SAU Community

Recommended Posts

Hello ladies and gents..

I have few leftover bits from my long gone R33 series 1. Taking room in the garage and giving my folks an excuse to start a fight for taking up room so I need these gone ASAP. Located in the Hills area, Sydney.all prices neg..would be easier to contact me on 0405095954 for any questions,,cheers Hoody

Fujitsubo Giken exhaust in excellent condition includes a dump pipe,mid pipe and muffler, no dings or major scratches, all you need is a cat to bolt in, this system sounded excellent in my car and wasn't too loud but had nice deep roar in it when throttle was applied: $200

Pair of factory series 1 seats in excellent condition, no tears or holes, comes with rails (seats were stored sitting on each other so they little squished but little airing them should sort that out): $100 for both

Trust style front bar in flexible fibreglass and in excellent condition, comes with mesh aswell, bought this originally for $300, after couple of years due to car being low it was all mangled up, took it back and got it refibreglassed to new condition for another $200,,,then i breifly had it on car and then took it off,,so its like new,,comes with custom brackets to mount on,,,can also help to put it on $200

series 1 silver colour bonnet,,some surface scratches which should buff out,,straight bonnet $100 ..also second marron bonnet with little ding at front of it,,,free

pair of series 1 headlights,,these have some of the mountings broken but were glued back on and work,,the lenses were taken off as experiment but can be put back together,,great for parts or to repair and seal them back up $50

also have rear right disk and calliper,,$20

post-44195-0-45282000-1369135377_thumb.jpg

post-44195-0-68626200-1369135552_thumb.jpg

post-44195-0-08425600-1369135643_thumb.jpg

post-44195-0-43535000-1369135811_thumb.jpg

post-44195-0-56211000-1369135959_thumb.jpg

post-44195-0-71840500-1369136219_thumb.jpg

post-44195-0-56812800-1369136277_thumb.jpg

post-44195-0-61422500-1369136824_thumb.jpg

post-44195-0-04619500-1369136917_thumb.jpg

post-44195-0-85990100-1369136970_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/425659-r33-bits-syd/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...