Jump to content
SAU Community

Recommended Posts

i decided to sell some of my r33 parts and i found 3 ecu's, but i dont know what model they are from, i noticed a sticker on them that has what looks like different codes, does anyone know how to tell the difference between the different series and model ecu's?

one ecu i have has G8 on it, and the other 2 have TJ on them.

Link to comment
https://www.sau.com.au/forums/topic/426804-stock-r33-ecu/
Share on other sites

Ok after some research i found a list off all the ecu codes and what they mean

here it is if anyone else is every looking for it.

Posted by user: andygts

www.skylineowners.com


R33

23710-13U00 01/96-06/96 RB25DET MT F5
23710-13U01 06/96- RB25DET MT F5
23710-13U10 06/96- RB25DET AT F5
23710-15U00 08/93-01/95 RB20E MT
23710-15U10 08/93-01/95 RB20E AT F4
23710-15U60 01/95-01/96 RB20E MT F5
23710-15U70 01/95-01/96 RB20E AT F4
23710-17U00 08/93-09/93 RB25DE MT
23710-17U01 11/93-04/94 RB25DE MT 2WD+HI.2WD
23710-17U03 04/94-01/95 RB25DE MT 2WD+HI.2WD
23710-17U10 08/93-09/93 RB25DE AT F5
23710-17U11 09/93-04/94 RB25DE AT F5
23710-17U13 04/94-01/95 RB25DE AT F5
23710-17U60 01/95-01/96 RB25DE MT F5 2WD+HI/2WD
23710-17U70 01/95-01/96 RB25DE AT F5
23710-21U00 08/93-09/93 RB25DET MT
23710-21U01 09/93-04/94 RB25DET MT
23710-21U02 04/94-07/94 RB25DET MT
23710-21U03 07/94-01/95 RB25DET MT
23710-21U10 08/93-09/93 RB25DET AT F4
23710-24U11 09/93-04/94 RB25DET AT F4
23710-21U12 04/94-07/94 RB25DET AT F4
23710-21U13 07/94-01/95 RB25DET AT F4
23710-21U60 01/95-08/95 RB25DET MT F5
23710-21U61 08/95-01/96 RB25DET MT F5
23710-21U70 01/95-08/95 RB25DET AT F4
23710-21U71 08/95-01/96 RB25DET AT F4
23710-23U00 11/93-04/94 RB25DE MT 2K.4WD + 4S
23710-23U02 04/94-01/95 RB25DE MT 2K.4WD + 4S
23710-23U10 11/93-04/94 RB25DE AT F4
23710-23U12 04/94-01/95 RB25DE AT F4
23710-23U60 01/95-01/96 RB25DE MT F5 4S + GTS4
23710-23U70 01/95-01/96 RB25DE AT F4
23710-24U00 01/95-01/96 RB26DETT
23710-24U01 01/96- RB26DETT
23710-26U00 01/96- RB20E MT F5
23710-26U10 01/96- RB20E AT F4
23710-28U00 01/96- RB25DE MT F5 2WD
23710-28U10 01/96- RB25DE AT F4 2WD
23710-29U00 01/96- RB25DE MT F5 4WD
23710-29U10 01/96- RB25DE AT F4 4WD

Link to comment
https://www.sau.com.au/forums/topic/426804-stock-r33-ecu/#findComment-6886134
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...