Jump to content
SAU Community

Recommended Posts

Hey guys,

Over the next couple of months, I will be replacing various parts on my V35. Therefore, the stock counterparts will be up for grabs as listed below.

- Front bumper with aftermarket lip. Some scratches evident.

- Stock side skirts. Some scratches evident

- Non-brembo calipers + rotors + lines

- ?Brembo rotors

Open to offers on all the above

Body parts are painted black

Items located in Melbourne

Patience is requested from future buyers as I will be offloading these items as their after market counterparts arrive in the country.

Other items for sale;

1)

946921_10200743058691572_1611716823_n.jp

Brand: SSR
Model: MS1
Tyres: 225/35/19f 235/35/19r
Pair / Set: set
PCD: 5x114.3
Diameter / Width / Offset: 19x9.5 +18f 19x10 +24r
Condition: Small gutter rash on the right rear wheel, 1x wheel cap slightly damaged, other small imperfections due to daily use. No hairline cracks.
Location: Melbourne
Willing to Ship: At buyers expense
Price: $3000
Willing to Swap: No, but keen to see what you got. Negative offsets, only 19x10-11 inch wide!

2) JL 13W7 in ported box (not carpetted) and JL 1000/1v2 amplifer for sale!

Can throw in all cabling required. Items are not even 4 months old. Selling it as these were in my old car, and they will not obviously fit in the V35.

$1400 for both plus wiring plus FREE capcitor.

Link to comment
https://www.sau.com.au/forums/topic/427248-vic-fs-various-v35-coupe-parts/
Share on other sites

Bumpppp

Front non brembo rotors. Plenty of meat left. Have not even been machined once! $140 for both

1013699_10200890590899785_1753052125_n.j

Non brembo rear rotors. Same as above. $100 for both

993762_10200890591659804_621983186_n.jpg

Brembo slotted rotors. Little bit of life left in them (Maybe one pad life left depending on which pad you use) $100

1017370_10200890590699780_742746163_n.jp

Stock non brembo calipers with pads $200

1012611_10200890592139816_1886984897_n.j

Might be interested in the non-brembo rear rotors. Any chance you can do me a favour and measure the distance from the outer edge of the rotor to the outer edge of the hub? I found out one of my rear rotors is too small the other day and just want to check what size these are before committing to buying. The one of mine that is too small is 55mm, the other is 60mm.

basically this.

post-84647-0-08172800-1372108896_thumb.jpg

I discovered the other day that one of my rear rotors is smaller than the other and the brake pad is overhanging the edge of the disk.

I didn't have time to remove the whole rotor to confirm the overall diameter, but was able to measure the figure shown in the pic, the small rotor had a measurement of 55mm, the rotor on the other side which looked correct was 60mm.

I've got the original rear rotors of my coupe in the shed, and just measured them at 55mm (actually closer to 54mm). Both have a small un-worn (is that even a word) strip around the outer rim, so the pads definitely weren't overhanging the rotor. Just to clarify, I have a 2003 premium coupe, and these were the standard (non-brembo) brakes. Were there different calipers on different years?

I'm not sure, but I guess they must be, mine is an 05 350GT sedan, the rotor on the left side is quite close to 60mm and the is only a small strip around the edge that is unworn, like yours. But the pads on the right rotor overhang by about 3-4mm, which suggests the right rotor has been replaced with one for a different year/spec, but I can't find anything to suggest there are any differences, other than the brembos.

The Callipers and the pads on both sides look identical, so I am assuming it is just this rotor that is wrong and not everything except this rotor??

Thanks for checking though!

If it helps - my rotors are 292mm diameter & 16mm thick. The calipers have "15" & "4306" cast next to the bleed nipple, and "27A" cast above where the pads sit. I've got a full set of F&R rotors & calipers in the shed, so if you want any measurements or pics let me know.

Thanks for your help.. I actually created a new thread about this issue on the weekend.. I might post some further info in there if you are interested, instead of clogging up this 'for sale' thread.

Edited by sonicii

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
×
×
  • Create New...