Jump to content
SAU Community

Recommended Posts

I bought my car in May 2012. I was very impressed by the fact the car had all original paint and panels (with panel gaps that were 100% factory). However, the paint was not in the best condition....and I always thought my car looked a tad dull compared to other examples I've seen in real life and on the internet.

It is now in July 2013, that I have finally gotten around to restoring the car back to its former glory, sort of. The reason I say sort of is because the front bumper is pelted with rock chips, the rear bar is a scratched through the clear coat, and the bonnet has a fair few stone chips which would require a lot of brush touching.

Now, I drive this car on a daily basis. I strongly believe that a performance car is built to be driven, and also kept looking nice. I think it is a bit of a shame when performance cars rarely ever come out of the garage.

I believe you develop a better bond with your car by appreciating how to tackle all the shapes and curves of the car through detailing. I use a Dual Action Polisher, and with the correct pad and product selection, you CAN achieve the same results as with a Rotary, but with less risk. The only downside is it will take a bit more time.

Here is my album of photographs BEFORE starting the DETAIL.

http://imgur.com/a/lLaNY#0


I put roughly a LOT of man hours into this restoration. I did an extensive amount of prep work before I commenced a 3 stage polishing regimen with an aggressive compound, intermediate polish, and a jewelling polish.

& Here are my results....(the pictures taken are with a sealant applied after polishing, once I apply carnauba wax I will take the car out in sunlight and take more pictures). I haven't applied trim conditioners or anything either yet.

lg4P6Jk.jpg

lg4P6Jk.jpg

Mfm28Yj.jpg

kzvjwjt.jpg

uY87nWp.jpg

luSMWvI.jpg

qyYuA5U.jpg

pT5ezE7.jpgAm6kcAi.jpgXfK9qJT.jpggtOxfVF.jpg

2Rav3js.jpg

WlB1O5n.jpg

ar1kBUC.jpg

4ZPEOM8.jpg

eAMZqHo.jpg

ppMrHG2.jpg

  • Like 1

Would've helped if you noted which photos were which, as it's kind of hard to see the differences before and after detailing. Put them in some sort of order.

Not sure what you mean. The album link is all the before photos. Just a random assortment showing the paint has a lot of scratches, swirls, etching, general contamination etc.

The pictures posted in this thread here are after photos. As you can tell, there is none of that present in the after photos.

Well done mate looking sweet so far. Saw a random bottle of ammo - who stocks the stuff in oz?

Hi, thanks man.

I got my stuff via airmail from Ammo in America. I used AMMO skin to seal the car.

  • 3 weeks later...
  • 4 weeks later...

Well, it's now been close to 2 months since I completed the detail....

I spent some time today washing the car, and then I applied a layer of carnauba wax, let it sit for 45 minutes, then buffed it off by hand with a megs microfiber towel.

These pictures should give you a good idea of how the car looks in natural lighting in the afternoon.

The reflections really have a lot of clarity which I'm super happy about, as I was able to remove a lot of the factory orange peel in the paint when I went through the compounding to polishing phases (this was my one of my goals).

Roof

rdnG2ZJ.jpg

Roof

NrCSzSc.jpg

Hey Benji great job, just thought I'd ask is have you used autoglym super resin polish and hd wax before? You can source the polish via eBay for half the price retailers in aussieland can sell it for and the wax the cheapest I've seen is about $85 but seriously its easy to apply and easy to come off and it makes a fantastic difference

Hey Benji great job, just thought I'd ask is have you used autoglym super resin polish and hd wax before? You can source the polish via eBay for half the price retailers in aussieland can sell it for and the wax the cheapest I've seen is about $85 but seriously its easy to apply and easy to come off and it makes a fantastic difference

Hi Ken,

Cheers!

As for your questions:

Super resin polish - it is lightlyyyy abrasive but its downfall is it contains a lot of fillers. After you polish these fillers will be left to hide swirls or scratches. If you want to remove scratches completely you'd use a different product.

Hd wax - I am not too familiar with the HD wax...but if it is priced at $85 I assume it would be a good carnauba based wax.

I use Dodo juice supernatural carnauba wax (can get it from the UK for an ok price) applied over a base of AMMO NYC sealant (sealant is applied, buffed off with MF towel, left to cure for 24 hrs to bond to the paint, then I apply wax over the top). It is a really good wax and makes the paint absolutely look like glass, but it shares the downfall of any carnauba wax is it attracts a lot of dust. I'll only need to have taken the car out once or twice and there will be a fine layer of dust sitting on the car.

  • 2 months later...

Here is a picture of my car taken with an SLR camera....should give you guys a good idea of the finish.

Washing every 2 weeks and waxing every 4-6 weeks to protect and maintain the finish.

DAQbnNE.jpg

Oh damn love how it's turned out! all the panels look like they have a sheet of glass over it. love it!

Can definitely tell you've put a lot of hard hours into this and it's payed off!

Good write up with lots of pics, nice car! Its nice to see that your putting a lot of love into it even with the simplest things.

being a daily you'd want it to look nice not only for yourself but to catch eyes, one of my fav cars :worship:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
×
×
  • Create New...