Jump to content
SAU Community

Recommended Posts

Hi guys.
Id like to run a the triple gauge cluster as fitted to GTR/260RS etc in my GTS-t for the purpose of having a voltage and oil temp guage without having to run aftermarket items.
Was this an option on the GTS-t, or is it prewired at all?
If not, am i able to wire it in? Id assume the voltage guage would be quite simple. Will there be a fitting somewhere on the RB20DET to run the RB26DET oil temp sender, or will the RB20DET have a sender already, just not wired to a gauge?
For the boost gauge, would i be able to just wire it in parallel from the sensor mounted to the firewall that sends signal to the dash cluster? I know a second boost gauge is redundant but id rather have it working than sitting there with a non-moving needle.

Thanks in advance.

post-113393-0-91401100-1376567676_thumb.jpg

No, not an option on GTSt. Therefore no wiring in place for it. Also no oil temperature sender. To fit an oil temp sender you'd need to put a sandwich plate on the engine and fit the GTR's oil temp sender in that.

Volt meters are the single most useless gauge you can fit to a car. It's not the 1970s any more. You already have a boost gauge on the dash. Therefore 2/3 of the GTR 3 guage set is worthless. Therefore fitting one to a GTSt is pretty much worthless.

You'd be far better off getting a single-DIN mounting panel and 3 of the ChinaBay stepper motor guages (or proper Defi ones if you're flush for cash) that will actually do something useful for you. I did exactly this. Oil temperature - big check. Probably the single most important gauge you can fit to car that you thrash (other than a decent oil pressure gauge). Boost - wanted to make sure I had something more reliable than the stocker, which are known to tell fibs and also don't go high enough anyway. And I got an EGT guage. Very useful tuning aid, and also serves as a warning for leanouts. I got the ChinaBay guages that have peak recall and change colour to RED lighting when they alarm (go over the max setting). Cute.

Your desires may differ. I was torn between what I chose to get and the other option of losing one of those choices in favour of an oil pressure gauge. At the time my dash's oil pressure gauge was workign perfectly but since then it has started flaking out. If I were doing it again I might not fit the EGT and get the pressure gauge.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...