Jump to content
SAU Community

Raspberry Pi

Kenna802

By Kenna802,
in PC & Games Discussion

 Share

Recommended Posts

Kenna802 Experienced

Kenna802

Posted
Posted

Anyone had a play with this little device ? Was thinking it could be a cheap alternative as a media player/ computer by using 2 separate sd cards ( one with Linux and other with Linux xmbc ) obviously u can't run both at same time but it is a cheap little device.

Link to comment
https://www.sau.com.au/forums/topic/430539-raspberry-pi/
Share on other sites
  • 2 weeks later...
*LOACH* Veteran

*LOACH*

Posted
Posted

When I first heard about the Pi I thought it would be revolutionary but now you can pick up Android tablets for less than $50 which use a similar chip, already include a monitor, RAM, a drive and are functional out of the box. In addition I can just go to a shop and buy one whereas the Pi had (and maybe still has) a massive wait. I imagine it would be possible to run a Linux distro on most tablets without too much trouble too. For a media player you will need to spend a little more to get a tablet with a HDMI out.

Link to comment
https://www.sau.com.au/forums/topic/430539-raspberry-pi/#findComment-6992814
Share on other sites
  • 2 weeks later...
junkie Mentor

junkie

Posted
Posted

i have one... got it for free from a mate who works @ google

running raspbmc at the moment. works surprisingly well - the only thing i miss is built in wi-fi and i havent tried 1080p stuff on it yet

its controlled by the tv remote so no stuffing around with keyboards and mice. ill set it up as the garage media player one of these days

Link to comment
https://www.sau.com.au/forums/topic/430539-raspberry-pi/#findComment-7017335
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      Bit of a similar question, apprently with epoxy primer you can just sand the panel to 240 grit then apply it and put body filler on top. So does that basically mean you almost never have to go to bare metal for simple dents?
    • luke gtr
      Did tie rods. Steering now not "springing" back.

      By luke gtr · Posted

      Good to hear. Hopefully you're happy enough not to notice when driving and just enjoy yourself.
    • luke gtr
      Returning after a long time!

      By luke gtr · Posted

      I mean, most of us just love cars. Doesnt necessarily have to be a skyline.
    • luke gtr
      Returning after a long time!

      By luke gtr · Posted

      Did you pick up a manual cluster to remove the position indicator?  (Pretty sure the 34 has the gear position in the cluster, but it's been a while)
    • 33GTRV
      Rb26 iron block limit

      By 33GTRV · Posted

      Here is a recipe. Sonic blocks till you get one that has a good enough bore. Get a torque plate and block brace, use your choice of fasteners (arp ect) bolt the thing together empty, half fill it and let it cure. Release it when it has, go to a REPUTABLE RB Builder and get the thing line bored/honed and cylinder honed to size, then wash. Once its all clean and dandy, wash and blow it out again. Then again.  Assemble said engine to your desired clearances with oil control mods, gasket to suit desired CR/Squish ect. Attach your extended sump with proper trap door oil baffles and head drain plumbed to sump with a SUMP BREATHER SYSTEM. Build your front diff with a decent LSD, rebuild your transfer case with a few extra plates, more than likely replace your tailshaft centre bearing and tighten up the rear diff. Tune to minimise excessive midrange cylinder pressure (timing unless you like to split bores and rebuild engines) Enjoy your engine, but hate the fact you are now destroying engine mounts, gearboxes, gearbox mounts, diff output flanges and driveshafts, diff mounts, tailshafts and front CV's.   Disclaimer.... Ive never done any of the aforementioned stuff.......
×
×
  • Create New...