Jump to content
SAU Community

Recommended Posts

  • Replies 60
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Have you got the rear left side Trim which is located next to the rear passenger door??

post-106573-0-22889700-1379955255_thumb.jpg

Edited by Noopykid

hey mate im after the rear cradle as mine has a large rust hole in it

righto, I have an rs260 one (should be the same) which is in better condition.

Still has some surface rust on it though so you'd be best to come check it out for yourself.

PM me for more details.

My Stagea RSFourS had an unfortunate meeting with a curb(all front left damage).

So i basically need an entire front left setup, upper horseshoe arm, middle J arm(with ball joint), lower s shaped arm, hub assembly, drive shaft, track rod and end, tie rod, abs sensor and wheel arch liner.

So do you think you could help with all or any of these parts?

Thanks for your help.

My Stagea RSFourS had an unfortunate meeting with a curb(all front left damage).

So i basically need an entire front left setup, upper horseshoe arm, middle J arm(with ball joint), lower s shaped arm, hub assembly, drive shaft, track rod and end, tie rod, abs sensor and wheel arch liner.

So do you think you could help with all or any of these parts?

Thanks for your help.

Yea got all of that stuff. Flick me a pm to arrange.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...