Jump to content
SAU Community

Mugabetown - Whoretownin' At It's Worst.


Recommended Posts

If you can convince the company that they need you and couldn't operate profitably without you, you have a winning argument. Hence $20k raise at the beginning of the year. ;-)

that is very rare, as it is seldom that one person could have such an impact on a business. Especially in the resources sector

that is very rare, as it is seldom that one person could have such an impact on a business. Especially in the resources sector

If I amended that to 'as proftiably' would that be a more correct reflection? Of course, for this to occur, you would need to be at the top or very close to the top - especially within an arm of the business that closely related to sales.

If I amended that to 'as proftiably' would that be a more correct reflection? Of course, for this to occur, you would need to be at the top or very close to the top - especially within an arm of the business that closely related to sales.

it truly depends on the demographics of the business

Yes, if key senior personnel ie executives were to use their position as a bargaining chip to demand an increase in their remuneration package then it may work

Should it he reporting entity though - them auditors would be all over it

Especially the way the public now eyes deeply what how execs are remunerated

In a smaller sized business ie SME - most that are in a top position usually have the ability to influence everyone - making performance bonuses that much easier ;)

  • Like 1

Jawsome!

do tell how!

I was curious too so I did a little digging on the QLD/TMR site and I found this:

Moderately-Powered Vehicle Grounds

You may apply for a certifi cate of exemption if the car you wish to

drive was manufactured before 1 January 2010 and has:

• a supercharged or turbocharged engine, not diesel powered

• a power-to-weight ratio of not more than 125kW/tonne

• no other features of a HPV listed on this form.

You application must be supported by:

• a document published by the manufacturer verifying the

power-to-weight ratio, such as the owner’s manual or

information from the manufacturer’s website; or

• a specifi cation information test report.

A specifi cation information test report is issued by an automotive

service provider and must show:

• the name and address of the organisation(s) that conducted the

test(s)

• the date of the test(s)

• vehicle make, model, VIN/chassis number

• the vehicle’s kerb weight and maximum engine power

• details about the measuring system used to conduct the test,

for example, an engine dynamometer."

From what I've been able to find a stock 33 gts-t would have around 130ish kw/t if you're going off the factory engine and weight figures from nissan. That power to weight ratio wouldn't classify for an exemption however if you were to put the car on a weigh bridge and run it on a dyno it would most likely be under 125kw/t though. So I guess it's all up to which figures they take into account when doing the exemption.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Hi, i’m making a rb25det coil loom for Vag short coil. Can anybody tell me which Ecu signal wire belong to coil number 1 and 2,3,4,5,6? The connecting switch in above pic is 8 wire i think white is for +12v and black for earth.
    • Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
×
×
  • Create New...