Jump to content
SAU Community

Recommended Posts

Got this complete rear cradle from a Series 2 Rs4s Stagea.

What you see is what you get (not including the tailshaft and motor behind it!)

$600, need it gone from my driveway.

PICK UP Preferred however can ship. Due to the size it will probably be pricey for shipping but hit me up if you want a quote.

IMG_0694_zps09fb3cba.jpg

IMG_0693_zpse320200f.jpg

IMG_0692_zpsec281a58.jpg

IMG_0690_zps998bd91c.jpg

  • 1 month later...

Guys this is a bargain :) gtr axles and unis , "much stronger", lsd center and 50mm shorter so you can run 10 inch wide rims on the back :) if you plan on making over 300 and use it you will need one of these one day trust me

Guys this is a bargain :) gtr axles and unis , "much stronger", lsd center and 50mm shorter so you can run 10 inch wide rims on the back :) if you plan on making over 300 and use it you will need one of these one day trust me

  • Like 1

Guys this is a bargain :) gtr axles and unis , "much stronger", lsd center and 50mm shorter so you can run 10 inch wide rims on the back :) if you plan on making over 300 and use it you will need one of these one day trust me

cheers mate, yea it's cheap because I just have a lot of parts and would rather the space

get on it people!

  • 1 month later...
  • 1 month later...

Hey champ Im not sure if you are willing to seperate but I desperately need two within spec rear rotors ( over the 16mm minimum thickness ) if these ones are over that would you be willing to sell them seperate ?

Hey champ Im not sure if you are willing to seperate but I desperately need two within spec rear rotors ( over the 16mm minimum thickness ) if these ones are over that would you be willing to sell them seperate ?

yea can do for the right price, i'll have to check the thickness tonight though

  • 1 month later...
  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...