Jump to content
SAU Community

26/30 With Hks2530's

SIR-JD

By SIR-JD,
in Engines & Forced Induction

 Share

Recommended Posts

SIR-JD Rising Star

SIR-JD

Posted
Posted

Hey guys, I'm just about to dump my finished 26/30 into my 32gtr. I have a set of hks2530's from my old 26 to put on. I have been told these turbos are the equivalent to -5's. I want the car as a responsive track car. Do you think these turbos are a good match for my application?

The bottom end is fully built and the head has been rebuilt with 262's in it. Cheers

Link to comment
https://www.sau.com.au/forums/topic/432103-2630-with-hks2530s/
Share on other sites
Mick_o Grand Master

Mick_o

Posted
Posted
<br /><p>To answer your question about the gearbox im gunna say no ;) lol <br /> Be sure to" data-cid="7028654" data-time="1379658073">

Fantastic! That's exactly what I wanted to hear :-). I will also be running race fuel. The gearbox is a refreshed r33gtr item (better than the 32) I hope it is strong enough...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
    • r32-25t
      R32 gtr transmission strength, billet plate

      By r32-25t · Posted

      Wouldn’t touch par if they gave it to me. You need to ask how much power you’re looking to make and then add about 50% to it because that’s what you’ll end up making  The factory box says no more at about 350kw or so, the upgraded synchro boxes won’t handle much over 500kw for long and at that point you’re looking at an auto or dog engagement manual,  once you’ve gone dog engagement you may as well go sequential, they cost a little bit more but it’s worth it  also while you’re at it you should upgrade the transfer case with 10 friction plates 
×
×
  • Create New...