Jump to content
SAU Community

Vi-Pec Air Temp Sensor Through Airflow Meter Wiring

jamesdt

By jamesdt,
in Engines & Forced Induction

 Share

Recommended Posts

  • 2 weeks later...
jamesdt Enthusiast

jamesdt

Posted
  • Author
Posted

thanks for that guilt-toy i thought you could. im just trying to set that up now..

in the vi-pec manual it says that the airflow meter signal comes through An volt 4, but when selecting what input i want An volt 4 to run it doesnt list the bosch IAT sensor the same as an An temp setting does. whats the go ?

cheers!

post-111725-0-57779700-1381043145_thumb.png

Guilt-Toy Grand Master

Guilt-Toy

Posted
Posted

yeah its a pain in the ass, to do it this way you need to set IAT then set it to a calibration, then set the resistance for the sensor in the cal table.

you are better off calling your dealer and getting a expansion cable and run new wires to the sensor so you can use the pre-set calibrations.

jamesdt Enthusiast

jamesdt

Posted
  • Author
Posted (edited)

had a feeling this mite be the case. i was going to have to get an expansion cable sooner or later for running the ethanol content sensor. all good thanks for your help again much appreciated!

Edited by jamesdt

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Nightmare_mistress_R33
      CD009 RB Conversion

      By Nightmare_mistress_R33 · Posted

      Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • jez NF
      The Evolution Of "night Fury"

      By jez NF · Posted

      75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
    • jez NF
      The Evolution Of "night Fury"

      By jez NF · Posted

      Trailer prep is underway... Lined up the wheel to get a rough indication of how it would sit Then removed all the bits (as far as possible) and gave the frame a light sand and quick lick of paint   Then added some carpet
    • JC71
      gauge needle removal

      By JC71 · Posted

      okay, so I figured this out, removed needles and reinstalled after swapping the gauge face on my triple gauge for my ER34, all work and look good. I tried to do the same for the main cluster, but the main cluster gauge faces are dished, the replacement gauge face are flat, so due to the dish in the org face ,mounting backing plate (clear) and depth of the needle, the flat gauge face will not work. I notice that R34 gtr gauges are flat, appears to be different clear backing plate that aren't dished. are these available, or what have others done to install flat gauge faces?
×
×
  • Create New...