Jump to content
SAU Community

Recommended Posts

  • Replies 65
  • Created
  • Last Reply

Top Posters In This Topic

sounds exactly like an over-pressurised crank case - blowing oil past the turbo seals and piston rings. i bet after you've let the engine gear down running down a large hill and then pulled away, white smoke just plooms...

just make sure your crankcase can vent correctly, check your pcv and rocker breather valve are connected and free of any major restrictions and that your pollution gear (carbon canister) is connected and not leaking.

only a handful of things can cause that kind of smoke and almost all of them are ruled out because you have just rebuilt your engine. white smoke in your situation is indicitive of oil being spilled out post-combustion and smouldering (white) on hot pipes. the only thing i can think of that wouldn't be a pressurized crankcase (and isn't exempt due to the fresh rebuild) would be your turbo seals. unless your hks aftermarket turbo has done more than 100,000kms or has been run at more than 20psi for prolonged periods, i would first be checking all your emissions equipment and making sure it was all in order. first thing i suggest is connecting ALL hoses as per factory specifications. then, if it solves your problem, recconect it all one-by-one until you find the smoke-causing culprit.

all the best mate.

-wombat

Hoping someone can give me some advice on what maybe causing my GTR to blow smoke after a full rebuild. Its done about 300km's since rebuild, so i might be jumping to conclusions but it seems to be a fair bit.  

Hear's what i had done, bore and hone to suit 20' over JE pistons, total seal ring set, forged Argo rods, new standard nissan crank and bearings throughout.

Head has been rebuilt with new valves Todda bronze valve guides and new seats cut. Also had my sump modified with a Trust sump extension kit and a N1 oil pump. had all this work done by a engine shop up here and put the rest of the gear back on myself.

Built the engine keeping in mind i wanted it to be able to make about 400kw at the wheels in the future. I have HKS 2530 turbo's on now with ces racing dump pipes and apexi exhaust, plus upgrade injectors, fuel pump and Apexi power fc, mines airflow meters and huge intercooler and a HKS remote oil filter/cooler kit to help keep things under control.

Bit of a run down on what ive done, hope this will help in sorting my problem out.

It seems to blow nice thick white smoke after it has been idling at the traffic lights when i take off and after i have been decelerating into corners and then accelarating out. but if i cruise at say 110 on the highway for a little while then change down and go round some tighter corners and accelerate and take it to 5000 with boost it doesnt blow any smoke at all.

The car was off the road for about 6 weeks with no battery sometimes, is there a chance the power fc needs retuning?

oil catch can doesnt seem to be getting any oil mist in it, i have the pvc valve blocked off and the line into the rear turbo intake boot is also blocked of, would this effect my crankcase venting at all, and having total seal rings would this add to the problem?

Before i had the engine rebuilt it was running fine, no smoke i had the HKS turbo's on it then to so it makes me think that i cant be the turbo's. or is there a chance that because they have been sitting for 6 weeks the seals me have dried up or something happened?

The engine was tuned with all the above mods down south in melb except for the pistons, rings and rods etc. i was hoping because i didnt change anything that would effect the mean effective pressure of the engine eg cams, boost level, CR etc that i would be fine with the existing tune on the power fc before my rebuild.

Im going to try and put as many k's on it over the next few days and load the thing up hills etc to see if it comes good, and will also keep an eye on oil consumption/oil level increse aswell. Have spent big bucks on this engine and hope the engine shop did the right job with bore and hone.

hopefuly somone has some good news for me on what to try, Thanks

how does your catch can vent,

does it plumb back or just vent through a hose, if it plumbs back to the rocker covers, make sure the catch can has sufficient venting, if its running a filter, remove it incase its blocked.

did it have the catch can fitted previously?

Dean

interesting thoughts , one of the first things i tried was mucking around with the venting system. when i got the car (before the rebuild) it had a small catch tank on it. the hose that originaly runs to the pcv valve was removed from the rocker cover end (still connected to the pcv valve) and had some sort of bung installed in it and was just dangling behind the rocker cover.

turns out on closer inspection the hose had split half way down anyway so was prob venting well still. the two pipes pointing forward on the rockers were interconnected and one of the other pipes heads off to a catch tank, then another pipe from the catch tank goes back to the rear turbo intake boot. the other pipe on the rocker was just vented to atmosphere with a pipe heading down the fire wall.... dodgy setup!

so with the rebuild i decided to get one of those simple catch tanks that sits on top of the rockers, i set it up correctly and had everything connected... so when i was first trying to sort out my probs i thought it was maybe the new catch tank setup.

turns out it wasnt cause i tried disconnecting things one at a time. ended up with putting the old catch tank on but on the advice of peter at advan, set it up differantly. he said to block the pcv off completely, block the rear turbo boot inlet line completely, interconnect the two forward rocker pipes and vent the other two to a catch tank with the catch tank venting with a filter on it.

Does this sound right or wrong??

Ive read on the total seal ring instructions that because they seal so well that they can cause pcv problems and they reccomend installing a bung with a 1/16 hole drilled in it into the fresh air side of the pcv. interesting??

May be oil/crankcase pressure related as it got worse after changing the oil again at 500k's. new oil = higher pressure and too much pressure is going to put more stress on turbo seals etc, along with too much crankcase pressure. checked the venting tubes at the rocker and no oil mist at all, so im guessing their is no blow by probs.

intereting, seems to be plenty of possibilities and hope fuly checking comps tomorrow it will cancel a few out??

interesting thoughts , one of the first things i tried was mucking around with the venting system. when i got the car (before the rebuild) it had a small catch tank on it. the hose that originaly runs to the pcv valve was removed from the rocker cover end (still connected to the pcv valve) and had some sort of bung installed in it and was just dangling behind the rocker cover.

turns out on closer inspection the hose had split half way down anyway so was prob venting well still. the two pipes pointing forward on the rockers were interconnected and one of the other pipes heads off to a catch tank, then another pipe from the catch tank goes back to the rear turbo intake boot. the other pipe on the rocker was just vented to atmosphere with a pipe heading down the fire wall.... dodgy setup!

so with the rebuild i decided to get one of those simple catch tanks that sits on top of the rockers, i set it up correctly and had everything connected... so when i was first trying to sort out my probs i thought it was maybe the new catch tank setup.

turns out it wasnt cause i tried disconnecting things one at a time. ended up with putting the old catch tank on but on the advice of peter at advan, set it up differantly. he said to block the pcv off completely, block the rear turbo boot inlet line completely, interconnect the two forward rocker pipes and vent the other two to a catch tank with the catch tank venting with a filter on it.

Does this sound right or wrong??

Ive read on the total seal ring instructions that because they seal so well that they can cause pcv problems and they reccomend installing a bung with a 1/16 hole drilled in it into the fresh air side of the pcv. interesting??

May be oil/crankcase pressure related as it got worse after changing the oil again at 500k's. new oil = higher pressure and too much pressure is going to put more stress on turbo seals etc, along with too much crankcase pressure. checked the venting tubes at the rocker and no oil mist at all, so im guessing their is no blow by probs.

intereting, seems to be plenty of possibilities and hope fuly checking comps tomorrow it will cancel a few out??

sounds like ur catch tank is venting ok, but to be sure , leave the pcv blocked and the turbo piping pipe blocked and disconnect the catch can , so both rocker covers vent. then u will know for sure that the pressure is unlikely the crankcase.

i once fitted a catch tank to my gtr, but forgot to drill vent holes in the catch tank and i was leaving trails of white smoke down the street and pulling my hair out trying to work out what was going on, i also did lots of work, so was hard to pin point the reason, until someone pointed out that the catch tank wasnt venting.

did i feel like a butt head :(

yeah good point, definately good idea to try all the simple things before going rip tear bust again. any idea on how to pin point if its turbo seal problem? heard HKS 2530's are expensive to repair and not as efficent after the overhauls as no one can match the trims of the original HKS wheels?? dont want to pull them until ive tried everything.

considering this is a new engine rebuild, i would be putting my effort in to determining if its an engine problem.

as others have stated, sounds like venting, ring or valve stem issue to me.

you could try dropping the engine pipe and looking for oil, but considering the smoke isnt that bad, i would think that any evidence of oil would get burnt away pretty quickly.

im assuming your car is the grey r32gtr with the leather, cant remember the previous owners name, but if it is those 2530s on your car,they have already been rebuilt.

the turbos were mine , aswell as the afms, i sold them to ben and we had 2 failures. i definately bought 1 new core and i think ben used some parts from another turbo to repair the other.

i bought these turbos, thinking they were fine and got rolled and i footed the bill to repair them.

damn... second hand turbo's are a bit like buying second hand gearboxes... time bombs waiting to go off? so your thinkin it hopefuly isnt turbo related then, do you know how long ago they were rebuilt? would be becomming very expensive turbo's if their in need of more attention!

well after a long day at the work shop still no closer but have atleast cancelled a few things out. did a dry comp test, compressions were good so didnt bother with a wet. did notice something interesting though with all the plugs out, plugs in number 3 and 4 were alot blacker than any of the others. all the rest were burning nice and clean. here are the comp results...

CYL COMP PLUG CONDITION

#1 = 160psi clean

#2 = 165psi clean

#3 = 166psi black/brown

#4 = 174psi black all over

#5 = 165psi clean

#6 = 175psi clean

comps are good, bit of variation between 1 and 6 but nothing to worry about at this stage i think. so pulled the front pipes of to cat and started the engine with a few small pushes of the throttle after it was warm and noticed that both turbo's seemed to be smoking similar amounts. which makes sense compared to plug condition. so im thinking either the fuel is not atomising well in those cylinders or the valve stem seals are leaking in those cylinders. will put a AFR meter on it tomorrow and hopefuly this will cancel out a fuel problem. any idea what sort of time is involved in doing valve stem seals with head on??

Chances are you will have to by a VRS kit as the valve stem seals on their own are more expensive than the VRS kit.

For example the VRS kit I bought for my RB25head was $275.

Just for the valve stem seals they wanted $330.

i think , it sounds like u have eliminated any ancilary problems.

comp test still wont 100% eliminate a ring problem, likely would pick up a broken ring or ring land, but if your problem relates to bedding in or faulty ring or rebore/hone the only way is to tear it apart.

what about a bore scope , you may see some scoring in one of the bores.

if u cant find the problem and decide to pull the head off, i would just pull the engine, u will spew if u go to all the work pulling the head off to find its the engine.

been there done that!

its starting to sound like its going to be coming out.

well after a long day at the work shop still no closer but have atleast cancelled a few things out. did a dry comp test, compressions were good so didnt bother with a wet. did notice something interesting though with all the plugs out, plugs in number 3 and 4 were alot blacker than any of the others. all the rest were burning nice and clean. here are the comp results...

CYL COMP         PLUG CONDITION

#1 = 160psi           clean

#2 = 165psi           clean

#3 = 166psi           black/brown

#4 = 174psi           black all over

#5 = 165psi           clean

#6 = 175psi           clean

comps are good, bit of variation between 1 and 6 but nothing to worry about at this stage i think. so pulled the front pipes of to cat and started the engine with a few small pushes of the throttle after it was warm and noticed that both turbo's seemed to be smoking similar amounts. which makes sense compared to plug condition. so im thinking either the fuel is not atomising well in those cylinders or the valve stem seals are leaking in those cylinders. will put a AFR meter on it tomorrow and hopefuly this will cancel out a fuel problem. any idea what sort of time is involved in doing valve stem seals with head on??

doing valve stem seals with head on wouldnt be too time consuming, probably half a day at a guess.

ive still got my money on a ring problem.

(have u spoken to ben, he may be able to offer some advice)

havent spoken to ben yet but will try to call him today, one of the disadvantages of living up here... no one has any experience on these things. good idea with the boro scope, i have one at work i can use that we use to inspect gas turbine engine internals so it should do the trick. will go pick it up today and see what the bores and valve/pistons look like, hopefuly give me an idea...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • See if you can thermal epoxy a heatsink or two onto it?
    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1780, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
    • Also, I logged some data from the ECU for each session (mostly oil pressures and various temps, but also speed, revs etc, can't believe I forgot accelerator position). The Ecutek data loads nicely to datazap, I got good data from sessions 2, 3 and 4: https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-2?log=0&data=7 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-3?log=0&data=6 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-4?log=0&data=6 Each session is cut into 3 files but loaded together, you can change between them in the top left. As the test sessions are mostly about the car, not me, I basically start by checking the oil pressure (good, or at least consistent all day). These have an electrically controlled oil pump which targets 25psi(!) at low load and 50 at high. I'm running a much thicker oil than recommended by nissan (they said 0w20, I'm running 10w40) so its a little higher. The main thing is that it doesn't drop too far, eg in the long left hand fish hook, or under brakes so I know I'm not getting oil surge. Good start. Then Oil and Coolant temp, plus intercooler and intake temps, like this: Keeping in mind ambient was about 5o at session 2, I'd say the oil temp is good. The coolant temp as OK but a big worry for hot days (it was getting to 110 back in Feb when it was 35o) so I need to keep addressing that. The water to air intercooler is working totally backwards where we get 5o air in the intake, squish/warm it in the turbos (unknown temp) then run it through the intercoolers which are say 65o max in this case, then the result is 20o air into the engine......the day was too atypical to draw a conclusion on that I think, in the united states of freedom they do a lot of upsizing the intercooler and heat exchanger cores to get those temps down but they were OK this time. The other interesting (but not concerning) part for me was the turbo speed vs boost graph: I circled an example from the main straight. With the tune boost peaks at around 18psi but it deliberately drops to about 14psi at redline because the turbos are tiny - they choke at high revs and just create more heat than power if you run them hard all the way. But you can also see the turbo speed at the same time; it raises from about 180,000rpm to 210,000rpm which the boost falls....imagine the turbine speed if they held 18psi to redline. The wastegates are electrically controlled so there is a heap of logic about boost target, actual boost, delta etc etc but it all seems to work well
×
×
  • Create New...