Jump to content
SAU Community

Recommended Posts

Hi Everyone,

I am new to the forum, and stumbled across this forum while contemplating if getting a R35 would be the right choice of car for me. I don't have a abundant knowledge of the car other than the typical (Most bang for buck supercar) out there.

Unfortunately price is always a factor when purchasing cars (At least for most people :no:) (especially when it is purely going to be a weekend toy). My budget would probably be around $100K to $110K.

I have heard some notorious stories about the running cost of these beauties, but had recently test drove and talked to a dealer about it. Not sure if this is entirely true but from what he says, the cost have come down dramatically, mainly because of after market stuff. E.g Brake and disc replaced no longer cost $6000, more like $2500. And tyres are around $2000 for a full set. This is obviously a huge factor to take into account before the taking plunge.

Something they had offered which was quite appealing to me was that they had the extended warranty packages up for purchase, which covers all the original manufactures warranty. Though the question then becomes, if you start installing all these after market parts, does it void all the warranties.

Lastly, if anyone can share any insight experience in what to look for when purchasing a second hand R35. E.g Tyres, brakes, logbook, etc.

Regards,

Link to comment
https://www.sau.com.au/forums/topic/434155-looking-to-learn-more-about-gtrs/
Share on other sites

Installing after market performance parts will void warranty.

You just don't want to pick one up that had been heavily modified and brought back to stock.

If you get a transmission problem with no warranty your talking 10's of thousands I think..

READ the warranty PDS, as i deal with it allot in my work, generally any aftermarket parts are not covered by warranty, depending on the conditions this does not usually VOID a warranty however if you have a failure due to your modifications then you are out of luck.

this is up for interpretation, not your interpretation btw so be careful.

but if you fit different brakes and your ECU dies, then its not going to be linked is it.

READ the PDS.

A wise man ounce told me if your buying a performance car to afford to keep it running you must be able to buy 2 of them.

Its like any car, you get some really tough ones, then you get some real lemon's.

Of course when it comes to modifying you got to totally ignore the warranty as they will totally ignore you.

I have seen some in that price range from dealers so I think you can get your hands on one with no mods.

If your looking for some thing with a little more ponies though,

I think you will have to spend a little more, cost of car and maintenance.

Edited by Bubbles

Thanks for the feedbacks,

Its definitely food for thought, starting to sway to maybe getting one and scrape all these warranty business. Seems the better option is to fiddle with the car and have mods instead and if things do go wrong, order better parts to replace it lol.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
    • And if you have to drill the oil block, then just drill it for 1/4" and tap it BSP and get a 1/8 to 1/4 BSP bush. The Nissan sender will go straight in and the bush will suit the newly tapped hole. And it will be real strong, to boot.
    • No it doesn't. It just needs an ezy-out to pull that broken bit of alloy out of the hole and presto chango - it will be back to being a 1/8" hole tapped NPT. as per @MBS206 recco. That would be for making what you had in alloy, in steel. If you wanted to do just that instead of remote mounting like @Duncan and I have been pushing. A steel fitting would be unbreakable (compared to that tragically skinny little alloy adapter). But remote mounting would almost certainly be 10x better. Small engineering shops abound all over the place. A lathe and 10 minutes of time = 2x six packs.
×
×
  • Create New...