Jump to content
SAU Community

Recommended Posts

Auto Electrician rang to ask where diagnostic port is.

Can anyone tell me where exactly the port is on a NM35 Stagea?

I just said "have you looked around the driver n passenger foot wells?"

Auto Electrician rang to ask where diagnostic port is.

Can anyone tell me where exactly the port is on a NM35 Stagea?

I just said "have you looked around the driver n passenger foot wells?"

Might be time for a new auto electrician.

That's what I was thinking. Lol. They come highly recommended around town and alot of business gave em a good wrap. Probably just lazy to look.

Hopefully your right.

But as pn-mad said it is driver side.

They reckon they have found a loom of wiring that is corroded really bad near the location of the battery with water pooling. They cutting it out now and going to replace that section and going to keep the old section to show me.

They reckon they have found a loom of wiring that is corroded really bad near the location of the battery with water pooling. They cutting it out now and going to replace that section and going to keep the old section to show me.

There have been a couple of these lately; it might be worth everyone checking.

A stitch in time; saves nine. ;)

Yup, turn car off remove key, open the fuse box in the drivers side footwell, and stick your hand down there as far as you can. See if you can feel water, or moisture. That will mess up your electrics real quick. I make a habit of clearing the crud from the plenum area, right down to where the drains are in the bottom of the guards. Mud and crud build up over time.

Got the Stagea back from the Auto-Elec yesterday, a big chunk of wiring loom got replaced and everything is running sweet once again.

Taken it for a few drives with no problem.

So great warning for people, make sure you clean out your drainage points regularly because its not worth the problems if you don't.

Got the Stagea back from the Auto-Elec yesterday, a big chunk of wiring loom got replaced and everything is running sweet once again.

Taken it for a few drives with no problem.

So great warning for people, make sure you clean out your drainage points regularly because its not worth the problems if you don't.

Good to hear it's sorted, definitely a timely reminder for everyone else.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
    • Just one thing; tapping tapered threads is tricky. Taps are always tapered and you would generally run it as far as you can, but with a tapered thread you have to stop much sooner otherwise the wide part of the taper will run in too far and you will have to thread the sensor in too far too as well (possible that it will never make a good seal) BTW nice wide wheels, I guess the top one is for the back!
    • Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity. Edit: 11kg each (or 10.9/11.1 depending on what my scale decides over multiple tests, the 18x11 don't seem to weigh noticeably any more than 10.5)  
×
×
  • Create New...